Architectural Woodworking

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Barn siding for kitchen island

1/18/15       
antonio

Website: http://www.positivewoodworks.com

Hey guys, so we have this kitchen island to do for a client that calls for a tight curve. They want it to look like rustic siding. Im thiking an american walnut barn type siding. Im thinking we would buy this as t & g reclaimed lumber but whats some good ways to get these to make a curve. Take a look at this pic i snagged off a website. Its kind of like this curve here.


View higher quality, full size image (990 X 660)

1/18/15       #2: Barn siding for kitchen island ...
james mcgrew Member

The base looks segmented plank from the photo. at a 44" plus radius this will look cool. if you have to do say 18 or below you may have to plane down the non visible back and pray it will bend

1/18/15       #3: Barn siding for kitchen island ...
antonio

thanks james,,,, thats pretty much our first guess at doing it,,,, but always open for suggestions

1/19/15       #4: Barn siding for kitchen island ...
mark

I can't tell if that photo is of a residential or a commercial location... Nice stairs, but the bar, eeek: I wouldn't be looking for inspiration there. At any rate, the T&G won't help you any with curved work.

1/19/15       #5: Barn siding for kitchen island ...
antonio

mark i have no idea where this place is or what it is,,, i only used it because it shows a 'curved island' that had some form of vertical planks going around it which is kind of what the client asked for. Maybe what i am seeing in this pic is not t & g , probably a 1/4" thick ready-made paneling. But it does have that t & g 'look' which is what the client is looking for. So like i mentioned before.........looking for suggestions here to get it done.

1/19/15       #6: Barn siding for kitchen island ...
james mcgrew Member

You may have to remove the tongue and bevel the edges back a bit lead a good 1/16 th +/- for expansion (if it is old enough it may not have too much need)

1/19/15       #7: Barn siding for kitchen island ...
Bob

What about running the boards on the table saw length wise and cutting relief cuts about 1/2" apart. Cuts should be about 2/3 depth of the wood thickness. This will allow the boards to slightly cup to the radius of the bar.

1/19/15       #8: Barn siding for kitchen island ...
antonio

thanks bob! that was one idea we were toying with. We are going to get a few boards and give that a test.

1/19/15       #9: Barn siding for kitchen island ...
Leo G

Resaw the boards and make veneer out of them. Then just put it on a kerfcore substrate and bend it.

1/20/15       #10: Barn siding for kitchen island ...
antonio

thanks leo, you know, we have all the kerfcore literature & brochures but have not tried the products yet,,, i did wonder though if i could somehow use kerfcore to make this easier. Thanks will look into this further.

1/20/15       #11: Barn siding for kitchen island ...
Leo G

I've used kerfcore on one job. It's heavy and hard to work with if you are just a single guy like myself. If you have help it'll be easy.

Having a CNC available to make the ribbing makes the job that much easier, but not necessary.

I would suggest doing a sample with the barnboard veneer. Probably slice it to 1/9" and widebelt it as thin as you can get it so it doesn't crack. Probably 1/32"-3/64".

It's much easier to use then bending plywood to get a flatter more stable surface

1/21/15       #12: Barn siding for kitchen island ...
rich c.

You could use matching shaper cutters, one concave, one convex. The boards will basically nest together like a roll top desk. They sell small router bits like this for strip canoes.

2/3/15       #13: Barn siding for kitchen island ...
Rick Mosher  Member

Website: profinisher.blogspot.com/

Sounds like a basic coopering job to me. Only you don't need a compound bend. Just cut the correct bevels (A full size mockup will make it easy to determine the angle) and put it together like a barrel.


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)