We finished a fairly big job and have been paid in full.
The customers move in and discover their custom wall cabinets are 12" deep and thought they would be deeper. They never mentioned deeper cabinets to us, they thought they would be the same as their old house, never thought to mention it.
We didn't ask as all of our showroom cabinets, which they saw, are 12".
Their drawings show 12" although probably not as clearly as it could. (Cabinet Vision)
They would like them rebuilt and for us to absorb half the cost. We can reuse all the face frames and doors except for two corner cabinets.
What do you think?
For what it's worth, they have been a pain to work with.
A PIA customer is still a customer who's word of mouth is invaluable . His good referal keeps the chain strong a bad referral breaks that chain . I get industry standards and contracts but isn't satisfying a customer just as important . I'm just a small fish and I'd redo the uppers at no cost whatsoever except for a bunch of apologies .
I sounds to me as if you did all you could do A) you provided plans, B) you were not exposed to the previous house nor was it stated,
There is value in Cabinetry even if it ends up in the work shed or Garage. sit with them. look at the total value, give them the break that helps you sleep, obviously 50% is too high, offer to hand the reused cabinets in the garage and the discount is less. or take them with you for a little more, Donate them to Habitat and take the tax deduction
I personally wouldn't absorb half the cost. It sure sounds like you did everything right and if they were in your showroom and didn't notice it until their large items wouldn't fit in the uppers that's on them.
It's not to say I wouldn't work with them to make it right and soften the blow a little but 50 percent is way too much for something where there is no shared reslonsibility.
They can go to any number of other places and see the same depth cabinets. I'm assuming your not taking about slightly deeper (an inch).
It would be irresponsible to walk away from this situation even though ethically you could certainly make a case for doing so. All these critical dimensions should have been discussed beforehand so there are no surprises. I often am asked to make uppers 15" deep as the standard 12" is quite shallow, I don't find it to be an unusual request. This one just fell through the cracks; It happens. If they are offering 50% and you only have to replace the boxes and handle installation issues, I think you should do it. Might make you look like a real hero in their eyes. At least they will have the special kitchen they envisioned.
Architects and designers are used to things being a dimension, a 36" door is 39-1/2" wide with casing but they specify a 36" door which is the clear opening. How deep are your lowers? Do sinks fit or are you 24" lowers deeper?
I am talking about the dimension from the face of the wall to the face of the door.
The issue is shop drawings should always show a clear inside dimension.
We build 13-7/8" to face of door which is 13" box and 12" inside by default. We build lowers 24-7/8" to the face of the door. If we build less or more there is a ID dimension shown on the architectural drawings.
The only question I have is if you make new boxes what happens at inside corners if there are any.
You have to decide if winning the battle is worth the potential "bad advertising" or won't refer your company in the future.
I think a big part of this, that of course only the OP can quantify, is that the customer has already apparently been a pain in the a $$. The chances of a customer like that suddenly turn into one that runs around singing your praises and winning you work is slim to none even though that still leaves a chance.
I don't think anyone is saying tell them flatly no, but the 50% implies there was MAJOR error on the part of the OP. It doesn't sound to me as that is the case. It sounds like they were in his showroom, looked at cabs, we're given a drawing with likely a multitude of dimensions they probably just ignored. Now upon moving in they realize their stuff doesn't fit like it did in their old cabs and may possibly be implying that "custom" cabinets are somehow deeper by default. Not true.
I would work with them and may offer to build the boxes at cost and charge a reduced rate for tear out and replacement but that'd be it. If they want to keep the old cabs and hang them in the garage that's a reduced cost for the boxes as the hanging as well even though you'd likely drag them back to the shop and give them away or burn them.
The fact that they were a pain in the a$$ has to be set aside.
Did your drawings clearly and simply specify the interior dimension? Do you point out the interior depths specifically, asking if there are things that require special dimensions? There is no industry standard other than yours, and it is your job to specify it. Assumptions are not only foolish, but will eventually cause trouble.
I'm thinking they were a pain in the ass because both you and they made assumptions - assumptions that were not dispelled by good drawings and communications. It is your job to clarify everything you do.
Both god and the devil reside in the details. If you are not detail oriented, you are lost.
The customers move in and discover their custom wall cabinets are 12" deep and THOUGHT they would be deeper. They never mentioned deeper cabinets to us, they THOUGHT they would be the same as their old house, never THOUGHT to mention it. -
Do you have to treat grown adults (with money) like 5 yr olds? Major problem with our society is no one takes responsibility for themselves. It's always "not my fault, "you" should have brought to my attention, what "I" wasn't thinking of".
I'm sure you don't have anything else on your plate.........
If they needed deeper wall cabinets they should have brought that in on their "want/need" list. Like drawers, trash cans, ect.
What are you a mind reader? I would accommodate them by offering a quote "full price with a--hole discount applied" on new wall cabinets anywhere they wanted them. To ease the blow I might consider reusing the doors and dispose of the others at no charge.
You will get no positive referral from them even if you ate 100 percent. If you enjoy a kick in the teeth, be flexible, they will not disappoint. You did your job when they were in your show room and they were supposed to look at the drawings.
I realize this does not help the OP, but this is an excerpt of the information sheets I supply with each proposal. It might help someone else in the future. Don't ask how I came to include it in my proposals:
"Note on available depth space for upper cabinets: the standard dish / dinner plate ranges in size from 9 to 10 1/2". All our cabinets are built with a standard cabinet depth of 12". Since they all have backs (the structural wall behind the cabinet is not visible), the available space in our cabinets is 10.90", well within the space needed. If you have the need for a deeper cabinet, please let us know. They can be built deeper, at additional cost. This option would be clearly stated in the options list. We suggest base cabinets with rollout shelves or drawers with or without plate racks as an alternative for oversized dishware. " Mario
1. Anyone who deals with the public runs into customers who are "difficult".
2. As professionals, we want our customers to be pleased with our work.
When we encounter 1., then 2. Is not always achievable.
We always try to explain to customers what they are going to get. Drawings are necessary, but not always sufficient for them to get it. Bear in mind that they are not experts and arrive with their own assumption set.
Most problems come down to a failure to communicate and a series of tacit assumptions.
How would you like to be treated in this situation. Do you feel that they had enough to understand that they were getting 12" uppers?
If the answer to that is an unreserved yes, then your contract is complete and you should withdraw gracefully. Obviously you will stand by your work.
If, however, you feel that they may have a point, then you should try to accommodate them in some way, as suggested in other answers.
If for no other reason, you will feel good and know you did what as right.
Here's what I'd do. Pop the backs off,if they're stapled they're likely history. Use a track saw and cut the groove or rabbit off to get a clean edge, make a reverse face frame the thickness you need , allow a 1/16'' or so reveal so as not to fuss over making it flush,I'd make the top rail wide to act as a nailer and attach using biscuits ,glue and screws. Reattach back and rehang. You might have to fudge the front face frames some to deal with the deeper cabinets, hopefully you used wide enough stiles to begin with. With a little hand finishing of the inside back face frames it should work. Beats starting from scratch and losing all the boxes.
As for myself, I always bring up the depth thing, explain that 12'' is standard and uses sheet goods most efficiently, but personally use deeper cabinets due to modern plates being often times deeper. I charge accordingly for deeper cabinets. The customer always appreciates the suggestion as it rarely enters their minds.They go home and measure the stuff they have, and often as not opt for the deeper cabinets.
OMG. What kind of pusillanimous businessman doesn't demand that adults act like adults?
JimHerron has it exactly right -- these are not 5 year-olds. And nobody is a mind-reader.
The only fact that matters is that their drawings show 12", as Gary stated.
It doesn't matter that it might have been more clear -- every drawing ever made could no doubt have been "more clear" from someones vantage point.
There's no need for perfection in clarity, only a presentation of facts that a reasonable person can understand. If an inside dimension of 12" is indicated in the drawings then that's the end of that.
The customer got the facts and assuming they signed off on them they are solely responsible. Period. That being the case, they don't deserve a dime of allowance and I wouldn't give them one.
They want them rebuilt deeper, fine, they can pay 100% for the rebuild. They want the not-deep-enough 12" cabs installed in their garage or wherever else, fine, they can pay for that, too.
Why do people allow themselves to be run over by jerks and losers who never, ever admit that any problem is of their own making or the result of their own inattention to obvious details they should have been paying attention to?
The customer is NOT always right. And the customer who thinks he is isn't just a customer, he's a problem and a loss waiting to happen.
I think maybe the non-mind-reading customer interpreted the drawings similar to how you have interpreted this thread.
You assumed "...an inside dimension of 12" is indicated in the drawings . ..."
Nowhere in this thread did the OP stipulate the 12 inch dimension was an interior useable measurement. If you, an obviously fearless sesquipedalian, cannot differentiate between inside dimensions and outside dimensions how are we to expect a (jerk like) civilian to know the difference?
For the same reason you expect a customer to be attentive to obvious details how can you not expect the OP to be responsible for grey areas? The jerk only buys a custom kitchen once or twice in her life. The OP does this for a living.
If you can't differentiate between inside and outside dimensions, how can she?
I have been in the shop for 42 years and I can tell you that anyone that tells me a "custom wall cabinet is 12"" would get a series of uncomfortably probing questions from me. That alone is meaningless language. If they worked for me, they would also get the lecture about meaningful terminology, and the one about assumptions.
Cabinet interior depth of 12" is meaningful. Overall depth is 12", including overlay door is meaningful. "Industry standards" is something to cover your ass - since you say "custom' everywhere - and implies hiding responsibility.
Industry standards and custom are mutually exclusive terms. As soon as you state 'custom' you then have the responsibility to define all the things that anyone might assume, and give solid facts.
Lazy language, lazy specifications, lazy communications will eventually hang you.
O.K. so the clients in this case are not a favorite type but none the less they have payed the piper .
They may never refer your shop ,
but they might .
A tad more clarity and communications prior to building is needed for some folks.
even though it was in writing , maybe they didn't catch it , it is our job to educate and communicate to the scope of what we are selling .
More importantly is the fact that not all people understand the same way , so you need to become better listeners to become better at selling what they want , the way you want to build it .
Turn this problem into an opportunity , I am not saying to work for free but perhaps a compromised offer not a lot different then what they offered you in the end may be best.
I Agree with Tim , figure something out be done with it . Some folks may never be really satisfied , thank goodness it is not that often , else we'd show up with a nail gun .
"The point is 12" was on the drawings -- and, once again, assuming they signed off on it -- that's the end of it."
The mentality in the retail market and the wholesale market are different.
I have had ladies say this is not what I thought it was going to be, you will have to redo it.
I then would ask why they signed the shop drawings if it was not what they wanted?
She would say I did not understand the drawings.
True I could go to court and win. But is it more trouble than just fixing what they want, in this case it was rebuilding an entire library. This was near the end of the job on a very large house.
I think the time spent on getting them to understand is time well spent. Also build policies as you go on how to handle this. E.G. make the upper cabinets deeper than 12" to accommodate bigger plates.
We had a miss communication on the color of some large counter tops which was not my mistake. So I relaminated them in the right color, not a small amount of work, we ended up doing every one of their stores with a very good relationship.
I mean if it came down to it what would it really take to rebuild the cabinets?
How come a 3'-0" door is a 3'-0" clear opening but a 12" deep cabin is an outside dimension with no reference to an ID?
Google how deep should a kitchen cabinet upper be and we get a WSJ article that says 12" isn't deep enough.
a 12" deep cabinet with no back and visible naliers probably is deep enough, same with a cabinet that back that is stapled on.
If one does a captive back with nailers behind its 3/4" to 1" taken out of the space.
if you build 24" deep base cabinets to the face of the door with a thick splash are all the sinks fitting in the tops?
How come a 2" x 4" is not 2" x 4", I mean common I am buying a 2 x 4, If I needed a 3.375 x 1.5 I would order that.
Oh wait that's standard. Shop drawings should show what your standards are, the guy down the street didn't do the job so if his 12" works (12" door thickness plus back thickness plus nailer thickness) it just doesn't matter, he didn't get the order.
One of the few kitchens we ever did was a batch of lowers that were 6" taller than the usual 36" net - for a NBA player. The original cabinet supplier had added 6" to the 4" toe kicks and charged an additional several thousand dollars for a day's work. It looked terrible.
As we started drawings, nothing was assumed, and every detail was examined, since no one wanted that to happen again. The owner was delighted with the 'no surprises' outcome.
If one can gain massive further business from some deal where a problem arises because the end-user isn't bright enough to pay attention to rudimentary, simple stuff like cabinet depth (or whatever,) then, absolutely, by all means, do so.
Accommodate them. Humor them. Lose money by bending over backwards for them.
But, that isn't the case in Gary's example.
12" was on the drawings. The end. They want something else? They can pay for it.
I built my own cabinets and none of them are less than 13" ID, but if I were a cab guy building kitchens, this sort of thing would lead me to have a very long checklist of stuff that every buyer would have to sign off on, item by item -- height, width, depth, wood, finish, hardware, slides, etc, etc., cabinet by cabinet after discussing each item. Initials on every line. Not just drawings.
Nobody would be able to say "this is not what I thought it was going to be" or "I did not understand the drawings."
And there would be no freebies, no matter how much other business might be gained.
With any luck, every customer would understand exactly what they are going to get -- no ambiguities.
Of course, not all of the people who aren't bright enough to inquire about the depth of their cabinets will be caught by any checklist, no matter how long it is but at least you'll be covered by it.
Those that slip through that procedure and then demand unreasonable stuff just have to written off. They're so used to doing it and getting away with it that they expect you to accommodate them, no matter what they signed or initialed.
They think that they're entitled and there's nothing you can do about that other than to do no further business with them.
The upside of a checklist type of procedure is that it might alert you to an problem-child type of customer before you obligate yourself to work for them.
Which is probably a good thing -- my experience in a number of businesses is that about 2% of all customers cause about 98% of all problems.
In my experience you are better off trying to assuage a customer's issues rather than being a hard ass.
Nobody really wins if you go to court.
I agree with the 80 - 20 rule or 2% - 98% rule, true words. You have to be aware enough that if you are dealing with a 2% er it does't matter what you do they are not going to be satisfied. In which case yup that is why you have policy to circumvent these people.
I'm big on checklists. The Emyth is basically a book about checklists and they work.
Your policys should be updated to include the problems you have run into. Really the Constitution is just policies taken from other countries that worked well to prevent problems from reoccurring.
Time spent getting the homeowner to understand what they are getting through specs, a showroom, 3d drawings are all time well spent, especially with women.
But the overarching policy should be to create a product/service that the customer is satisfied with if at ALL possible.
I would tend to think it would be worth rebuilding the uppers on this job for free.
FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards(return to top)
WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
A valid email return address must be included with each message.
Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
Subject lines may be edited for length and clarity.
"Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.
You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.
WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.
Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).
Libel: Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.
Improper Decorum: Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).
Advertising: The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).
Repeated Forum Abuse:
Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.
There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).
The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)
Forum Posting Form Guidelines
The name you enter in this field will be the name that appears with your post or response (return to form).
Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
Thread Related Link and Image Guidelines
Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
Thread Related File Uploads
Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .FLV .MP4 (Image Upload Tips) If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)
The editors, writers, and staff at WOODWEB try to promote safe practices.
What is safe for one woodworker under certain conditions may not be safe
for others in different circumstances. Readers should undertake the use
of materials and methods discussed at WOODWEB after considerate evaluation,
and at their own risk.