Woodworking Business

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Quality control in automated shops

9/28/17       
Curious

We have a pretty automated shop. The workflow runs through our engineering software, and directly out to all of our machines on the floor. As we're primarily panel processers, most of the work goes off of the machines and are nearly complete.

Today we had a rush order for 60 simple components, banded all 4 edges. I engineered it and sent it to the saw. I made it out to the shop floor as the last part was going through the bander. Out of curiosity, I asked the bander operator if he checked the final measurement of the part (with banding). He said no. I asked the person putting them on the pallet, again no. Asked the shop foreman, and no.

I put a tape on it and there was no problem. Long story short, If we engineer everything correctly in the office, we RARELY have an issue. Our rework rate is very low, but I worry about some detail being missed on a high quantity project. I hate the thought that our customers could get something that we should have caught.

What are other automated shops doing to ensure they catch errors sooner than later? Or are they?

9/29/17       #2: Quality control in automated shops ...
TonyF

Curious:

While I have not worked in automated shops, a few things struck me from this episode.

First, when the phrase "rush job" is the mantra for a particular project, perhaps the focus is on completion and deadline adherence rather than on quality.

Second, it appears as though there is no human in your process that has been delegated the responsibility of overall quality control. But you already found this out.

Finally, I think that even the most automated of industries still rely on the human touch to ensure that the product that goes out the door passes muster, even if it is only to throw a tape measure on it.

You might consider yourself fortunate that this process glitch revealed itself on a relatively small order.

One person whose job is to ensure quality throughout the process would probably be better than telling each workstation to be responsible for their aspect of it, as the latter may lead to a lot of finger pointing.

Good luck.
TonyF

9/29/17       #3: Quality control in automated shops ...
cabmaker

You might consider empowering someone in your company to be in charge of quality control and then rewarding them for that.

I don't know anything about parts manufacturing but I know a lot about boutique kitchens. There is a more or less finite number of possible places a cabinet can crash. These can be things like using the correct swing on door hinges or making sure everything is marked well or sanded well. For a glass door cabinet it might be simply remembering to measure for the glass and/or get it ordered.

With a simple checklist someone can certify that a cabinet is complete and ready to ship. It takes just a couple of minutes or less to go through the list and put a check mark by each event. If you paid one person a $10 bonus for each cabinet they certify you would be out a couple hundred bucks at the most and they would stand in line for the opportunity to be the Quality Assurance Guy.

When confronted with any kind of consternation out on the job site it costs the contractor absolutely nothing to say to you "We can't figure out what goes where.......can you send a guy out?"

When you are solving problems out on the job site you are solving them on somebody else's schedule. The cost of just one trip to remediate confusion will be a hundred times what it takes to make and laminate one single list.

When everybody is responsible nobody is responsible. If your system of management depends on somebody remembering to do something you will regularly surrender money.

9/29/17       #4: Quality control in automated shops ...
cabinetmaker

There are 2 kinds of shops:

Office controlled and run

Shop floor run and run (amuck)

If it is engineered from the office and banding was subtracted through the software, then the parts should be right

If you want the parts checked, send a note to the operators via shop drawings to check the parts as they come off ......

We shipped 70k worth of panels 7 states away- you had better believe the office and shop double checked each and every part as they came off and got loaded

Of course, then again, we make clients even count the hardware when we deliver and then ask them where they intend the product until installed. We note that on the shipper and our office keeps a copy and their office/pm gets a copy

(it's so much fun to have a PM from companies a little smaller than Halliburton calling to get copies of our documentation)

For quartz and granite, we have clients initial polished edge approval, sink placement and cut out, and seams, etc and what do ya know ?

9/29/17       #5: Quality control in automated shops ...
Alan F. Member

We put parts out at finish size, no edge subtraction, premill amount is adjusted after an edge sample is run on a per edge basis.

9/30/17       #6: Quality control in automated shops ...
rich c.

When I was a young pup in 1973, Caterpillar had a great investment in inspection personal in the factory. Inspection were made after each set up of a machine to start production. Then random daily checks by the same inspector. Each operator had a hammer with a code on it, and the operator had to stamp that code on each part. That provided a path back to someone running scrap. More training was provided when scrap numbers became too high. Operators were constantly checking with go, no-go gages. Today, each cell operator is responsible for verifying all dimensions are in tolerance. They use point to point digital arms to verify if the accuracy requires it. In any modern woodworking facility, I would suggest each operator should be trained to inspect and verify their own work after running the first part, and then random checking after.


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)