CNC

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

outline breaks mortise shoulder for blind tenon

2/24/19       
Gerry

We do a blind tenon for out cabinet backs and are having an issue where the outline cut breaks the shoulder on the mortise. We are running a Thermwood CS45 router and a .5" cutter at 16,000 rpm and 600 ipm.

If anyone has any suggestions on how we could resolve this I would appreciate your input. We can do outline cuts in 2 passes 1 being climb and the last conventional but that would cost a lot of time.

TIA


View higher quality, full size image (2080 X 1560)

2/24/19       #2: outline breaks mortise shoulder for ...
BH Davis  Member

Is this something you've done successfully in the past and is now suddenly not working? If so have there been any changes made to procedure, materials, tooling etc.?

Or is it a new process you are trying to incorporate?

BH Davis

2/24/19       #3: outline breaks mortise shoulder for ...
Gerry

BH,

Yes we have been running our cabinets like this for some time and would have this problem rarely. The last small run we did more than 1/2 of the mortise shoulders were broken.

The only thing that has changed is we moved the router to a new shop. I suspect the the gantry may have been taken out of square in the move but don't know how that would cause this problem. I am going to check it for square tomorrow.

Thanks,
Gerry

2/24/19       #4: outline breaks mortise shoulder for ...
BH Davis  Member

Gerry,

If this had been a new process for you my response would have been "what do you expect.....it's particle board." Obviously now though that isn't the problem.

Unless that is you somehow have a bad batch of material with weaker than normal glues.

However the fact that the machine has been moved is a huge red flag. I don't see how out of square could cause this to happen but do see other potential issues from the move.

I'd think things to take a second look at would be machine leveling, machine vibration potential (more an issue I'd think on lighter duty machines vs. heavy iron equipment), z-axis squareness to the table, vacuum hold down strength (material vibration potential) and probably even more issues that don't come immediately to mind.

You could also run some stand alone test dovetails in a scrap piece of material while closely studying all components including material to see if anything out of the ordinary can be seen or felt.

Probably checking for squareness as you suggest is a good place to start but also a thorough go over of the machine install to see if anything pops up.

Good luck,
BH Davis

2/24/19       #5: outline breaks mortise shoulder for ...
Gerry

BH,

I agree, I am going to give the machine a good going over. The material is from a new supplier so that could be an issue but I think checking the machine is a good place to start.

I don't think we are the only shop cutting our back in like this so I was hoping someone else who does this might have some input. Or maybe we are the only shop trying to do this ;)

Thanks,
Gerry

2/24/19       #6: outline breaks mortise shoulder for ...
Tom Gardiner

How about cutting your grooves after doing the cut out pass, assuming the parts will not shift.

2/24/19       #7: outline breaks mortise shoulder for ...
Gerry

Tom,

I have not found a way to do that in the software yet but I think it would be a good fix. We are using the the Thermwood control nesting software.

Thanks,
Gerry

2/25/19       #8: outline breaks mortise shoulder for ...
BH Davis  Member

Gerry,

Another thought. Are you climb or conventional cutting that perimeter cut out pass? Whichever it is you could try reversing the cut direction. Maybe not a long term solution but it might help you figure out what is happening.

BH Davis

2/25/19       #9: outline breaks mortise shoulder for ...
Gerry

BH,

If I do a climb cut it leaves a rough surface on the PB and I need to come back with a conventional pass to clean it up. That is time consuming and I would like to avoid it if possible.

Thanks,
Gerry

2/25/19       #10: outline breaks mortise shoulder for ...
Bob Lewis

We inset the backs an 1/8" to leave a little more meat on the shoulder

2/25/19       #11: outline breaks mortise shoulder for ...
Gerry

Bob,

That is a good idea. I will give that a try.

Thanks,
Gerry

2/26/19       #12: outline breaks mortise shoulder for ...
Mike

Gerry, I got the same machine. I use a 3/8 compression and also set my back in and have this happen very rarely. We also use 3/4 backs and rebate those out, so 3/8 slot in ends,top,bottom and the back gets 3/8 rebate.

2/26/19       #13: outline breaks mortise shoulder for ...
Gerry

Mike,

Good to hear I am not the only one who does their backs like this. I shortened the tenon on the top and deck and that closes the mortise on the end but leaves a little daylight in the corners which I don't care for.

I will play with some of these suggestions when I I get a little time.

Thanks,
Gerry

2/26/19       #14: outline breaks mortise shoulder for ...
Pat Gilbert

Are the top panels in the picture the backs or the ends?

Trying to follow along.

2/26/19       #15: outline breaks mortise shoulder for ...
Bob Lewis

With the backs in an 1/8th I rarely get the shoulder breaking. When a job requires flush backs, I do get some breakage.

2/26/19       #16: outline breaks mortise shoulder for ...
Gerry

Pat,

The pieces with the broken mortise are the top and deck of the cabinet.

Bob,

When you install do you shim the middle of the back to prevent it bowing?

Thanks,
Gerry

2/26/19       #17: outline breaks mortise shoulder for ...
Bob Lewis

Never needed to shim. The inset back allows the cabinet to have a better chance of sitting flat on a wall that is not flat.
Does that make sense? lol

2/26/19       #18: outline breaks mortise shoulder for ...
Larry

Hard to tell from here but... It looks like the PBd broke very uniformly near the bottom of the cut. That would seem to indicate particularly weak internal structure of the board. Make some trial cuts in different board and see if it makes a difference. Try MDF and some high quality PBd.

2/26/19       #19: outline breaks mortise shoulder for ...
Gerry

Bob,

Yes that makes sense to me, I do lot renovation work and the walls are lumpy bumpy and never plumb or square ;) I am sure it would help the cabinets sit flatter on the wall.

Larry,

I think the core is too soft on this board. We have quite a bit of it in stock so I will need to work around it for the short term.

Thanks,
Gerry


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)
    Onsrud Cutter Vortex Tool Company T-Tool USA