
You are not logged in. Consider these WOODWEB Member advantages:
A personal "member history" that displays your posts at WOODWEB
Your forms at WOODWEB will be filled in automatically
Create your personal "My Favorites" page
Numerous automatic notification options
Learn more about WOODWEB Member benefits ...
Blades for a slider -- 0 -- 
11/14

We are currently using FS Tool blades for our Felder slider and have found that they warp a lot. Not sure if we will get them again. Has anyone else had this problem and what blades do you find work the best. Have tried to hammer them out but with mixed success.
11/15 #2: Blades for a slider ...

You need a thicker plate. AKA a better quality blade. Call schmitdt tooling supply or any other local tooling supplier and tell them what your cutting. Do you need triple chip, ATB, Aggressive etc. I've only ever had cheap freud blades and the like warp.
Once you buy better blades and cut with them you will never go back to the hardware store .
We even run the high end blades on our regular chop saws. It makes a huge difference in finish cut and quality.
11/16 #3: Blades for a slider ...

try a set of stabilizers, cheap, might do the trick, however calculate in to see if you have offset for scorer, but there is no substitute for quality, consider better blades
11/16 #4: Blades for a slider ...

We use a mix of Leuco, Leitz and Forrest blades on our slider with no problems. Most are 12" and 14" and have plates about .110" to .125"; larger diameter blades have thicker plates. Are you misusing your blades, like ripping thick stock with a high tooth count blade? I've never had warpage problems, and thought FS Tool was a reputable outfit. Have you tried discussing the problem with their tech service?
11/16 #5: Blades for a slider ...

Sorry not sure of the replies. I was under the impression that an FS Tool blade that is 135$ from our industrial supplier was a quality blade. We are not a hobby shop and no stabilizers will not fit on our triple pin arbour of the saw.
11/16 #6: Blades for a slider ...

We use Leuco blades on the slider and beam saw. Their scoring blades (beam saw) are much better than others. We have an FS blade for the Omga and it has been fine. Is the blade being run hot? Dull, too slow of feed, wrong tooth pattern for the use?
11/17 #7: Blades for a slider ...

We use FS tool blades and have good luck with them on our slider. I would check the saw setup if you haven't, as in travel of slider parallel with blade, check saw arbor and flange for run out with a dial indicator and rip fence alignment
You didn't say what type of blade? Is it used for panel stock or solid?
Gerry
11/17 #8: Blades for a slider ...

XL4000 S23250 60T 10" .126 plate run at 6000rpm for melamine and pc plywood panel sizing only.
11/17 #9: Blades for a slider ...

I am running two of those blades both 12" and they are always in rotation on the saw with no problem going on at least 5 years cutting the same materials.
I could be wrong but I remember running my 10" saw at 4000 rpm. Might be worth a try to drop the rpm.
Gerry
11/19 #10: Blades for a slider ...

I am running FS tool blades on my SCM slider with out any issues. They cut great. I cut melamine and multi core prefinished ply'd and some mdf. Have you had troubles with any other blades, have you checked your saw?
11/19 #11: Blades for a slider ...

I had a lot of problems with a sharpening service destroying blade after blade. And, not hobby blades- a lot of them were FS Tool. You probably need to ask them some questions. We have run FS, Amana, and Freud without any problems once we got away from them.
11/23 #12: Blades for a slider ...

I think your rpm is way too high, even for a 10" blade. Heat build up causes shorter blade life and warping. 4500 rpm should be better, and less noisy too. You can always increase your tooth count.
11/23 #13: Blades for a slider ...

Following this thread, I am about to order blades for a slider coming in.
I need to rip 1" that burns a little easy and cross cut the same. Some times cutting upto 2".
Hoping for some recommendations for blades. I would guess a positive rake angle is preferred as the rake would pull the stock tight to the slider. Anyone using negative rakes on a slider?
Brands? I have been looking at some Skarpaz. Are they a quality blade? I know you get what you pay for...... looking into FS tool and Forrest as well. Though my Frued 24T rip industrial has been a good go to blade on my unisaw for years. Unsure if when stepping up to 12" I should also be considering thicker plate.
Anyone know if the cut is coarser on a 30T 12" as opposed too a 30T 10"? Seems the tooth spacing will be further aprt on the larger diameter blade. Does it make a difference?
0 -- 
Buy & Sell Exchanges | Forums | Galleries | Other Resources | Site Map
Buy and Sell Exchanges
Job Opportunities and Services Exchange
Employment opportunities and services within the woodworking industry
Lumber Exchange
A worldwide buy/sell exchange for lumber and wood products
Machinery Exchange
A worldwide buyer and seller exchange for woodworking machinery and equipment.
Classified Ad Exchange
Classified advertising for the woodworking industry (for advertisements that do not include machinery, lumber products and employment listings)
Forums
Adhesives Forum
Discussing topics related to adhesives within the woodworking industry
Architectural Woodworking Forum
Discussing quality standards and production of architectural wood products
Business and Management Forum
A forum for the discussion of business topics: from sales and marketing to dealing with difficult customers.
Cabinet and Millwork Installation Forum
Discussing all aspects of installation issues encountered by cabinet and millwork installers.
Cabinetmaking Forum
Discussing 32mm and face frame cabinet construction including fabrication, casegoods design, and installation.
CAD Forum
Shedding light on the all-too-often shadowy world of CAD.
CNC Forum
Discussing CNC (computer numerically controlled) woodworking equipment, software, and automated product manufacturing.
Dust Collection, Safety and Plant Operation Forum
Discussing topics related to maintaining a safe and productive working environment.
Professional Finishing Forum
Finishing issues for the production environment
Forestry Forum
The science and art of forest cultivation and timber management, planting, surveying, tree diseases, silviculture and timber harvesting
Professional Furniture Making Forum
Helping professional furniture makers improve quality, save time, and increase profits
Laminating and Solid Surfacing Forum
Issues related to laminating and solid surface materials and processes
Commercial Kiln Drying Forum
Discussions covering issues faced be commercial drying operations that process at least 750,000 bd. ft. of lumber per year
Sawing and Drying Forum
Discussing topics related to primary processing and drying of lumber
Solid Wood Machining Forum
Discussing topics related to the machining of solid wood
Value Added Wood Products Forum
Learn how to improve your output, find new markets, and boost sales of your lumber products
Veneer Forum
Discussing topics related to veneer processing, manufacturing, and fabrication
WOODnetWORK
An electronic discussion group for woodworkers throughout the world
Galleries
Project Gallery
Where professional woodworkers can post examples of their work
Sawmill Gallery
Professional primary processing companies display and describe their sawmill facilities
Shop Gallery
Professional woodworkers display and describe their shop facilities, products and equipment
Shopbuilt Equipment Gallery
Professional woodworker's jigs, rigs, and shopbuilt equipment
Other Resources
Industry News
Late-breaking news from all sectors of the wood industry
Video Library
Index of industrial woodworking related digital videos on the web
Auctions, Sales and Special Offers
Advertisers offering woodworkers discounted prices on good and services, and announcements of upcoming auctions
FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)
WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
A valid email return address must be included with each message.
Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
Subject lines may be edited for length and clarity.
"Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
(return to top).
Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.
You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.
WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.
Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).
Libel: Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.
Improper Decorum: Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).
Advertising: The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).
Repeated Forum Abuse:
Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.
There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).
The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)
Forum Posting Form Guidelines
|
Your Name
|
The name you enter in this field will be the name that appears with your post or response (return to form).
|
Your Website
|
Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
|
E-Mail Address
|
Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
|
Subject
|
Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
|
Thread Related Link and Image Guidelines
|
Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
|
Thread Related File Uploads
|
Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .FLV .MP4 (Image Upload Tips) If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)
|
|
|
|