Increasing chainsaw life

      How to keep your chainsaw mill in healthy, working order. January 16, 2001

I recently purchased a Husky 350 (50cc) and made my own jig, fashioned after the Alaskan. What can I do to help the life of the saw? I have a ripping chain installed, and give the saw a break between cuts.

Forum Responses
I've graduated from an Alaskan III mill with a Husky 262 to a Logosol with a 288 Husky. You've got a good start by listening to your saw, especially in hardwood.

I use 10W30 motor oil in my bar oil reservoir, and that eliminates a lot of heat. Eliminating most of the bar clamp except for what the 2 nuts hold helps get rid of sawdust quickly (watch your fingers!). Alternatively, you could ensure that debris is kept clean from the clutch area. On a good day I could cut about 120 bf.

I'll assume you use the Husky mix. The small containers mix with 10 liters of High Test gas.

At such high RPMs, your saw is like a vacuum cleaner. Blow out your air filter every time you fill with gas.

I disagree with using 10W30 as bar oil. Use the highest grade bar oil you can afford. If you have to, use gear oil 85/140 or 90--anything that has the ability to resist being thrown off the bar, like Hypoid gear oil. Regular bar oil has the correct additives and will stay on the bar long enough to lubricate it.

A clean air filter and high grade mixing oil are important.

My 044 is getting a new cylinder and piston. The saw had 5 gallons of gas, properly mixed with the Official Stihl Oil. But I used 87 octane and apparently this contains too many additives for a two stroke.

Set your carb to run a bit rich. Don't go for the "scream" of the saw. Do not add more or less oil to the fuel.

Years ago I did a lot of work with an Alaska Mill, and ended up with a double-ended bar and two of the largest power heads I could find. The power varied from time to time.

Run your power head fuel mixture as rich as possible when putting these high output units under heavy, continuous load. Youíll get improved internal engine cooling and lubrication.

Yes, give the power head a rest. They were not designed to operate for extended periods of time under heavy load.

Don't buy the line about 87 octane gas containing too many additives for a two stroke engine. The carburetor had to have been adjusted too lean for break-in purposes. A new engine needs the richest possible mixture for break-in, as the oil in the fuel mixture is what provides the lubrication for the piston/cylinder, as well as the crankshaft. This is from a long-time two-stroke mechanic.

Regular 87 octane gas was okay until recently, when they began adding oxidizers and other stuff (as much as 10% by volume) to meet air quality standards. The only way to beat this game, and to avoid premature gum formation, is to move to a higher octane.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Primary Processing

  • KnowledgeBase: Primary Processing: Sawmilling

  • KnowledgeBase: Knowledge Base

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2019 - WOODWEB ® Inc.
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review WOODWEB's Copyright Policy.

    The editors, writers, and staff at WOODWEB try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at WOODWEB after considerate evaluation, and at their own risk.

    WOODWEB, Inc.
    335 Bedell Road
    Montrose, PA 18801

    Contact WOODWEB

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article