Structural Support for "Floating" Wall Shelves

Good ideas for building strong shelves on site with no visible means of support. March 4, 2007

Question
I have a customer who wants just open shelves for upper cabinets, no sides or face frames, with really nothing holding them at all but a 1 1/2 rail under the shelves to attach to the wall. These will be 12" shelves. What would be the best way to support them? I was thinking she is going to at least have some sort of support on the ends. I think the longest shelf is going to be maybe 80" long. I was proposing 1 1/2 solid stock (oak) and cutting out the outside corners to fit solid stock, nailed and glued, then installing solid 1x2 frames on outside edge of shelves. Also the square corner stock will be attached to another shelf, which will get nailed to the ceiling and trimmed out. Any ideas? These will be all be made of oak and be stained, so no caulking on these cabinets.

Forum Responses
(Cabinetmaking Forum)
From contributor J:
This sounds like a job for a torsion box shelf. Ian Kirby did a couple of articles on these in magazines like Woodworker's Journal and a long time ago in Fine Woodworking. You might also look into using hardware such as the blind shelf supports that Lee Valley sells.



From contributor B:
I don't really understand the construction you are talking about in the last part of your post. But for cantilevered shelves, there are a few ways to go. The Lee Valley hardware looks good; also Hafele makes some that have cams on the shaft so you can adjust the shelves level.

Once I had a client who wanted these, and wanted 14" deep shelves that could hold a bunch of heavy books. So I made slabs of solid mahogany, 1-1/2" x 13-3/4". I then bored 3/8" or 1/2" holes through the planks, spaced 16" apart, with a long auger bit - so these were 13-3/4" deep holes. Then I lag bolted the sucker to the studs. I countersunk the lag bolts a few inches and got the longest lags I could find, so they went deep into the studs. When installing, it was easy to mark the wall where the lags were to pre-drill through the drywall and into the studs. The other thing I did was, I beveled the back of the shelf a few degrees so that in its resting state, the shelf would be canted slightly upwards. That way when weighted down, it would be level. When the shelves were up, I covered the lags with a 1/4" x 1-1/2" strip of solid mahogany, and then sanded and finished in place. Bear in mind that this is not really an easily removable installation. But those suckers could carry a lot of weight.



From contributor R:
I have built many of these shelves. There are two ways I like. One... rip a 2x10 and use 1/2" lags long enough to go through the edge of 2x and sink about 3" into studs. (You will be drilling the pilot holes through the edge of the board.) If you cut the 2x a bit short for longer shelves, the shelf can slide left or right as needed. You will need to build the shelves with a cavity to slide over the 2x. Careful! You can dent and break drywall if you tighten with impact wrench. Or have 1/4" thick strap iron bent and predrilled. Cut out drywall over studs. Lag the iron (with 90 degree bend) to the stud and mud over them. Then attach a piece of 3/4 ply to the angle and slide the shelf over the ply. Will hold lots of weight! By the way, I overkill stuff.



From contributor R:
I just saw contributor B's response. Very similar. When using the metal method I described earlier, you can put an individual piece of ply on each metal angle and torque them up a bit to get adjustment for weight. I have done this with shelves holding encyclopedias. One customer wanted the shelves because he could remove them easily for painting and papering. The shelf that slides onto the 2x10 only needs a small screw or two to hold it in place.


From the original questioner:
Thanks for the responses - all great and gave me what I needed in a short time, which I needed also. Mission accomplished! Thanks, WOODWEB, for a great site.