Temperature Settings for Hot Melt Systems and Applicators

      Hot-melt glues exposed to air in the melting tank should not be heated above 325 degrees Fahrenheit. September 13, 2006

This article was provided by Pierce Covert of Glue Machinery Corporation.

What are appropriate temperature settings for hot melt tanks, hoses, and guns? These are the most frequently asked questions by hot melt users.

Many hot melt applicator and adhesive providers suggest users set the initial temperature at 325 for every zone of the hot melt system. Users frequently ask if they can set a temperature higher than 325 when the viscosity of a selected hot melt adhesive is very high and is hard to apply.

With higher temperatures the double bond (or -bond) of a polymeric molecule tends to open, creating two free radicals (when the temperature exceeds 325). Those free radicals are very unstable or reactive; and will spontaneously react with the surrounding oxygen from the air. As a result, hot melt adhesives are oxidized and aged upon heating in the melting tank.

It is noticeable that most hot melt adhesives basically do not form free radicals at temperatures lower than 325. When hot melts in the melt reservoir are protected with a nitrogen blanket or under vacuum, they will not be oxidized even though free radicals exist in the adhesives.

To insure precise application and limit adhesive degradation with high viscosity adhesives, set the tank at a maximum of 325 and raise the temperature of the hose and gun first. Since adhesives inside the hose and guns are not exposed to air or oxygen; they will have no chance to be oxidized. Actually, users can raise the temperature of melting tank above 325F but should always maintain the adhesive level at 80-90% of the total tank depth and insure that the adhesive is used regularly.

Most melting tanks are heated with heating pads, cartridge heaters or cast in heaters. These are typically focused on the lower portion or the bottom of the melting tank. If users constantly charge ambient hot melt adhesive into melting tank to maintain an adhesive level, the solid room temperature adhesive will also lower the temperature of the molten adhesive particularly at the surface level. In fact, the temperature of those adhesives on the top layer, which are exposed to the air, will not exceed the tank set temperature. Consequently, adhesive users may increase the setting temperature for the melting tank as well without worrying too much about overheating of adhesives. To prevent oxidation, always keep in mind that only those adhesives exposed to air (surface level) should be maintained at a temperature below 325.

Melt On Demand tanks are extremely effective at keeping adhesive in the tank at lower temperatures prior to use and should be considered.

In summary, we recommend that adhesive in a melter reservoir does not exceed 325 if it exposes to air. If hot melt adhesive users can ensure the temperature of the adhesive at the top or surface of the tank is lower than 325 through consistent filling/use, then the tank can be operated at higher temperature levels than 325.

This article was provided by Pierce Covert of Glue Machinery Corporation.



Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?


Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Adhesives, Gluing and Laminating

  • KnowledgeBase: Adhesives, Gluing and Laminating: Glues and Bonding Agents


    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.



    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2016 - WOODWEB ® Inc.
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review WOODWEB's Copyright Policy.

    The editors, writers, and staff at WOODWEB try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at WOODWEB after considerate evaluation, and at their own risk.

    WOODWEB, Inc.
    335 Bedell Road
    Montrose, PA 18801

    Contact WOODWEB











  • WOODWEB - the leading resource for professional woodworkers


      Home » Knowledge Base » Knowledge Base Article