You are not logged in. Consider these WOODWEB Member advantages:
A personal "member history" that displays your posts at WOODWEB
Your forms at WOODWEB will be filled in automatically
Create your personal "My Favorites" page
Numerous automatic notification options
Learn more about WOODWEB Member benefits ...
Fine tuning a table saw
8/1
I've been trying to tune-up my saw, it's a General Int Starshop wich I didn't know what I was buying at the time. I've had it for four years and never had a straight cut ! I posted a message not long ago saying that I had 1/2 mm difference from back to front of the blade and the response was that I could'nt bare this if I wanted to do joinery wich I agree. I have a job going and need to do just that; joinery, lots of it and until I change the saw I have to bear with it.
The trunnion bolts are tied to the the steel top and not to the cabinet so I loosened the 6 bolts but the thing doesn't budge at all. Know, I'm not even sure the miter tracks are machined straight. Can someone tell me what I can tune this saw and how I can spot check the whole thing to see what's straight and what isn't befor I take the machine apart and sell for spare parts ? Thanks
8/1 #2: Fine tuning a table saw ...
Website: http://www.curvedmouldings.com
The quick and simple is to make your fence parallel to the blade. This will solve your problem for ripping.
It will not however do anything to help with the miter slot alignment. For that you'll have to move the top on the bolts. My guess is you'll have to remove the top and drill all the bolt holes oversize. That will allow for some twisting to bring it all into alignment. I had to do this on a Delta contractors saw about 30 years ago.
BH
8/2 #3: Fine tuning a table saw ...
Website: http://www.turncent.com
Mike, give it up on it. It is a contractor saw, they have inherent design flaws that once aligned should never tilt. As nearly as I can figure it knocks it out when tilted. Try this simple test, spend about six hours aligning the blade with the miter slot, the fence is still aligned, make a rip, works great right, then tilt it to 45, make a rip, it will be out of parallel with the fence and your cut will either burn or wander, tilt it to 90 again, it will now be out of alignment. I think it is gravity. It is at this point you will say to yourself I will never buy a contractors saw again. The same goes for hybrids. the glove
8/2 #4: Fine tuning a table saw ...
Website: http://www.turncent.com
BTY b divies, I am not sure of delta contractors saws from 30 years ago but now they attach the trunnions to the underside of the table so moving the top only moves the top, doesn't effect the blade slot alignment. the glove
8/2 #5: Fine tuning a table saw ...
Well I think it costs money to learn. I'm gonna take your advice and give it up. I already spent more than six hours trying to figure out this machine. Thanks for the advice ! What would be a good tablesaw for production work where the the trunnions are attached to the cabinet and not to the top?
8/2 #6: Fine tuning a table saw ...
A whole lot of people will recommend the SawStop. You get a high quality saw with every imaginable adjustment built it for easy tuning.............plus the safety factor that doesn't exist on any other brand.
BH
SawStop
8/2 #7: Fine tuning a table saw ...
B.H. Are you talking about the new contractor or the original saw stop ?
8/2 #8: Fine tuning a table saw ...
Mike,
For me I'm talking about the original cabinet saw. However from what you were saying in your post I was thinking the contractor model may be adequate.
I haven't had my hands on one other than at the machinery shows but I completely trust the folks at SawStop to have duplicated the quality standards of the original in the new model.
I met the founders of the company back when the brake system was first developed and have stayed in touch with them over the years. I can tell you from first hand experience that this is a group of people that care every bit as much about the quality of their product as they do about the profitability of their company.
I will add that the brake system has saved hundreds of people from getting injured.......including one of the guys in my own shop.
BH
BH
8/2 #9: Fine tuning a table saw ...
Thanks for the advice everyone for the input.
8/5 #10: Fine tuning a table saw ...
I bought a used comercial saw stop and I have to say that customer service there is top notch. They bent over backwards to help me out. The saw is good quality and easy to adjust.
I had to try the test with the wiener, when I got finished with it too. lol
It performed as expected.
Kenneth
Buy & Sell Exchanges | Forums | Other Resources | Site Map
Buy and Sell Exchanges
Job Opportunities and Services Exchange
Employment opportunities and services within the woodworking industry
Lumber Exchange
A worldwide buy/sell exchange for lumber and wood products
Machinery Exchange
A worldwide buyer and seller exchange for woodworking machinery and equipment.
Classified Ad Exchange
Classified advertising for the woodworking industry (for advertisements that do not include machinery, lumber products and employment listings)
Forums
Adhesives Forum
Discussing topics related to adhesives within the woodworking industry
Architectural Woodworking Forum
Discussing quality standards and production of architectural wood products
Business and Management Forum
A forum for the discussion of business topics: from sales and marketing to dealing with difficult customers.
Cabinet and Millwork Installation Forum
Discussing all aspects of installation issues encountered by cabinet and millwork installers.
Cabinetmaking Forum
Discussing 32mm and face frame cabinet construction including fabrication, casegoods design, and installation.
CAD Forum
Shedding light on the all-too-often shadowy world of CAD.
CNC Forum
Discussing CNC (computer numerically controlled) woodworking equipment, software, and automated product manufacturing.
Dust Collection, Safety and Plant Operation Forum
Discussing topics related to maintaining a safe and productive working environment.
Professional Finishing Forum
Finishing issues for the production environment
Forestry Forum
The science and art of forest cultivation and timber management, planting, surveying, tree diseases, silviculture and timber harvesting
Professional Furniture Making Forum
Helping professional furniture makers improve quality, save time, and increase profits
Laminating and Solid Surfacing Forum
Issues related to laminating and solid surface materials and processes
Project Gallery
Where professional woodworkers can post examples of their work
Commercial Kiln Drying Forum
Discussions covering issues faced be commercial drying operations that process at least 750,000 bd. ft. of lumber per year
Sawing and Drying Forum
Discussing topics related to primary processing and drying of lumber
Solid Wood Machining Forum
Discussing topics related to the machining of solid wood
Value Added Wood Products Forum
Learn how to improve your output, find new markets, and boost sales of your lumber products
Veneer Forum
Discussing topics related to veneer processing, manufacturing, and fabrication
WOODnetWORK
An electronic discussion group for woodworkers throughout the world
Other Resources
Industry News
Late-breaking news from all sectors of the wood industry
Video Library
Index of industrial woodworking related digital videos on the web
Auctions, Sales and Special Offers
Advertisers offering woodworkers discounted prices on good and services, and announcements of upcoming auctions
FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)
WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
A valid email return address must be included with each message.
Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
Subject lines may be edited for length and clarity.
"Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
(return to top).
Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.
You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.
WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.
Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).
Libel: Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.
Improper Decorum: Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).
Advertising: The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).
Repeated Forum Abuse:
Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.
There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).
The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)
Forum Posting Form Guidelines
|
|
Your Name
|
The name you enter in this field will be the name that appears with your post or response (return to form).
|
|
Your Website
|
Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
|
|
E-Mail Address
|
Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
|
|
Subject
|
Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
|
|
Thread Related Link and Image Guidelines
|
Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
|
|
Thread Related File Uploads
|
Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .FLV .MP4 (Image Upload Tips) If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)
|
|
|
|
Member