Architectural Woodworking

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Sliding Door Track for a Radiused Door

6/27/17       
Pat Gilbert

Has anyone bent sliding door track for an interior door to accommodate a radiused (in plan) door?

See the picture, he wants it to work like a barn door.

TIA


View higher quality, full size image (1536 X 2048)


View higher quality, full size image (2250 X 3000)

6/27/17       #2: Sliding Door Track for a Radiused D ...
Keith Newton

Pat, this shouldn't be a problem if you can find a metal or machine shop with a roll bender, and use the standard flat bar rail, or round tube, and have the radius of the arc.

The flat bar type would be less critical, being more flexible on that axis, where your stand-off mounting plates will hold it.

Bends are hard to make all the way to the ends, so order longer than you need.

And I'm sure you know the door will need to be on the opposite side of the opening you show in the lower pic. You've got to have a clear wall for the door to park over when open.

First step is choose the hardware in your phone to text to your local metal shops, so they'll know exactly what you are needing them to do.

6/27/17       #3: Sliding Door Track for a Radiused D ...
Pat Gilbert

Thanks Keith

"First step is choose the hardware"

Do you have one in mind?

6/27/17       #4: Sliding Door Track for a Radiused D ...
Joe Calhoon

Pat,
I think you are in CA. Functional Fenestration sells tracks and they can probably refer you to a local company that can bend these for you.
As another source, Hafele sells Hawa tracks that are good.

6/28/17       #5: Sliding Door Track for a Radiused D ...
Pat Gilbert

Thanks Joe

I wonder if this sort of track could be bent without deforming it.

I also wonder about the 4 wheel carriage making the radius without binding.


View higher quality, full size image (687 X 578)

6/28/17       #6: Sliding Door Track for a Radiused D ...
Joe Calhoon

I don't know about that type track Pat. No experience myself but several shops have bent FFIs lift and slide tracks. It's a little different since it's bottom hung and there is a limit to the radius the bottom carriage will follow.
Your radius looks tight. Is it hung on the outside of the wall? In that case the flat bar type with single roller would work best. I don't think FFI has those.

6/28/17       #7: Sliding Door Track for a Radiused D ...
Dan

Hafele can do it with their Hawa Media 70 track. Contact their architectural department.

6/28/17       #8: Sliding Door Track for a Radiused D ...
Keith Newton

Pat, I would avoid the U shape with the wheels inside. You would be darn lucky to find someone who could custom bend that for you.

Just plug into google search, and you'll find lots of options from $50 to $500.

The tracks which are about 1/2" thick by maybe 1 1/2" or more tall would be easiest and most forgiving.

The full rounds should bend without deforming enough to matter.

If your capable of building the door, your next main worry, is that there isn't going to be any blocking inside the wall where you need to hang it on, so don't overlook that.

Rolling Barn Door Hardware Kit

6/28/17       #9: Sliding Door Track for a Radiused D ...
Alan F.

kncrowder

http://www.kncrowder.com/pdf/slidingdoor-cat-pages/page-7-curved-track.pdf

6/28/17       #10: Sliding Door Track for a Radiused D ...
Pat Gilbert

Thanks guys,

FWIW the Hafele product is done in Switzerland. FFI doesn't do any bending and weren't able to refer me to anyone yet.

KN Crowder looks promising but I already turned in the bid.

I was able to locate a local guy that can bend flat bar. He said as mentioned that a U shaped piece would crinkle and not work.

6/29/17       #11: Sliding Door Track for a Radiused D ...
TonyF

Pat Gilbert:

I don't know if you can use the defined radii in the available tracks or not; if not you might call them and see if their supplier can do custom.

TonyF

McMaster-Carr Door Hanging Posts

6/29/17       #12: Sliding Door Track for a Radiused D ...
David R Sochar Member

Pat - I have had radius pocket door tracks fabricated twice by steelworkers. They both had to do it twice to get it right. Tubular track will not bend.

The trolleys/hangers should be selected and you should be able to give the fabricator a piece of the straight track and a trolley and a decent drawing. Then you you have to explain that this really needs to operate like warm butter. They should be able to cut the curves with a water jet or some such digital thing to make the curves accurate.

6/29/17       #13: Sliding Door Track for a Radiused D ...
Pat Gilbert

Dave

Are you saying to cut the rails instead of bending?

6/29/17       #14: Sliding Door Track for a Radiused D ...
David R Sochar Member

Yup. Those metal guys have these machines that can cut perfect arcs in steel. One for the upper plan curve, then they roll the two outer sides, and then two more narrow arcs plan cut for the trolley wheels to ride on. Give them a drawing with a good radial info, and drew holes located. The trick is to get the welder to put away his 5lb hammer, and use a tender touch. $250 does it for us.

6/29/17       #15: Sliding Door Track for a Radiused D ...
Pat Gilbert

That seems like there would be a lot of waste.

6/30/17       #16: Sliding Door Track for a Radiused D ...
David R Sochar Member

The problem with one attempt was that the metal fabricator used short curved pieces to make the curve for the 2 - 42" wide doors on an 8' radius. This was false economy since the butt joints we not level, had weld on them, etc. Hardly smooth as butter. The second attempt had the steel cut out of one piece and was smooth and worked very well. We had two doors, so we speed the track at 2 pcs 6' long, with a center butt in the field. We used Johnson T-2000 track/trolleys, and the track was simpler, sort of a "T" shape.


View higher quality, full size image (1800 X 1350)

6/30/17       #17: Sliding Door Track for a Radiused D ...
Pat Gilbert

Thanks Dave

If you had your choice would you use staves or laminated plywood.

6/30/17       #18: Sliding Door Track for a Radiused D ...
Adam

We did this job 20 years ago. It was a gang of real wood interior doors hung on a track. There were (3) 36" solid mahogany on each side. They went into the walls like pocket doors. Divided a dining room from a living room in an open floor plan. 18' of doors that disappeared into the walls.

The customer wanted to be able to push on one side with their finger to push 9' of doors into a wall. We are all sailors. The Architect speced the Harken mainsheet traveler track and the doors were hung off of it.

The Harken guys often bend track. Its really no big deal for them. All depends on your budget. They will be low on friction if you go that route.

Harken Curved Track

7/1/17       #19: Sliding Door Track for a Radiused D ...
Pat Gilbert

Adam

I don't see any carriages on that page?

7/2/17       #20: Sliding Door Track for a Radiused D ...
bob

richards wilcox
www.rwhardware.com

7/17/17       #21: Sliding Door Track for a Radiused D ...
nathandavidson Member

It it interesting to know that it is actually possible to use existing tracking to have it bent to accommodate to the new door frame. I have always thought that bending it could damage it and you would have to change the entire track. It is good to be learning some new things every single day for our own DIY benefits.


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)