There is a time and place for pocket holes.
Educate your contractor on the benefits.
Actually made my first pocket cutter. 26 years ago. Have used different ones since. I now have a Ritter dbl pocket machine.
I have had customers ask about the pockets. Once I explain it to them. The most heard response is: "That's a good idea" I have never had any complaints.
For 30 years, I avoided two things: Veneer tape edges and pocket holes. I was - and still am - convinced they are the start of the fall from civilization we all have been fearing. Neither has ever been allowed in my shop. Both are an accommodation, an acceptance, of lower quality for "price point" concerns. What's next? Printed wood patterns on paper laminated onto man made boards? Peel and stick veneers? Contact cement?
I would equate pocket hole door joinery with the worst work in the world. Yes, I have been told I am a snob. More than once.
However, my top shop hand recently argued for the use of some pocket holes in a piece we were building. I allowed it since he 1. made a good case for it, and I have come to respect his ideas, and 2. it seemed appropriate.
Now this was not door joinery - that is all mortise and tenon, no exceptions. It wasn't case joinery, that is all plow and rabbet, no exceptions. Just a valance panel attached to the top, to carry a cornice molding assembly.
So, I will now say pocket holes have a time and place, but they are very limited. It is still terrible for right angle joints that historically would be mortise and tenon - no glue surface but butt glue, no real mechanical prevention of twist, etc.
Pockets have a place, not door assembly. I'm not of fan of using them for case assembly either. They won't pass AWI. Lots of face frame guys use them. You need a clamp system to keep the faces flush. You have to use 2 or more to a joint or there is little to prevent twisting.
I've used pocket holes for years and will continue unless they invent something better. Obviously they have their place, and a door ain't one of them. The original post didn't mention anything about a door so I don't think he is considering that. I use them where they can't be seen.
They are in my opinion indispensable in many operations, like say a light valence under an upper or using them as "clamps" until the glue dries. I've used them for drawer boxes on 1/2" prefin maple ply (no glue) on some cabinets in my house....7 years later and no issue. Of course the drawers could be made better and to higher standards but the point is they have performed well with pocket holes.
Dave, are you mortise and tenoning everything?
About 20 years ago, I watched a carpenter install multi piece cornice with biscuits for alignment and pocket screws as clamps. I was amazed by the speed and quality of his product. I bought my first kreg jig that night. I have been using pockets as clamps and biscuits/ dominos for alignment ever since.
Around that time, I was a trim carpenter by day, and a snob hobby woodworker by night. I wouldn't have even considered using pockets, plywood or edgebanding or even sandpaper (a proper surface must be hand scraped!) on any furniture or cabinet project I made. Then my wife asked me to build a table for my son for Christmas. I had one night to do it, and a poorly equipped shop. I used pockets for everything. The boy is almost 17 now, the table still in use, and every joint is still tight.
Now, I build furniture and cabinets for a living. I still would not consider the use of pocket screws fine craftsmanship, but they do have their place. And not every customer can afford the highest quality work. And I make regular use of a wide belt.
Barry - I ignored your question. We don't use pocket screws much, so I don't hear anything about it from customers. However, the customer would be about the last place I would expect to hear about pocket screws from.
Joinery and how and where it is used is my turf, and I prefer to not have customers tell me what length or thickness my tenon needs to be. Talk to me about design or woods or fit and finish, but stay out of the technical end. This is why you hired a professional.
Chris - Do we tenon everything? We do a lot of doors, so a lot of it is M&T, most of it is cope and stick. We are tooled up to make M&T many different ways, so we find it the best solution to many problems.
Furniture frames, web frames, face frames, and all the frame and panel work is all - M&T. We use the pocket screws also on jigs for fast and secure fixture making. That may be the primary use for the tool in our shop.
To each his own. Our shop gets a lot of what I consider neat work because we are known for our level of craft. If a shop only aspires to pocket screws, then that may be all they ever get. They just won't attract the more interesting (my opinion) work.
So they have their place, but should not be considered a primary solution.
As said, pocket screws have their place and are very useful. I used some in this cabinet and they saved me time and space during glue up and assembly.
Come on out, look, and if you can find them, you win the cup of coffee.
Oh yeah, I laid up the plywood shelves behind the doors with shop cut veneer tape too.
As I said before, I use them where they can't be seen. The bench pic above is a good example of when not to use them and the cabinet below it a good example of when to use them,(great looking work by the way). When I first started years ago I prided myself on joinery. Rabbet joints in the back of the sides to receive the back, mortise and tenon face frame joints, etc. It took a long time to build a set. In the end this is what I realized. Only a fellow woodworker would appreciate my time and effort that I put in on making all those joints, plus all those joints got covered up and no one ever gets to see it anyway. I now use pocket holes and save time and then devote that time to things that get seen like design, finish, etc. I've never had a single cabinet to fail in anyway using pocket screws.
I guess I could have used mortise and tennon to put this together….
Dominos would have worked….
But my price would have been substantially more and I probably wouldn’t have gotten the job. I supplied a beautiful, custom sized vanity at a reasonable price. That is what I do, it is called value. Pocket screws allow me to do that.
Let's keep in mind that this is cabinetry forum, if you do not like, or understand how to use, or see the value of pocket screw joinery, the professional furniture making forum can be found below. :-)
I do not wish to argue, but we each have to find our own way. I'll use "Commoner's" term 'value' - not to pick on him, but it sums up what we both are trying to say.
I would go nuts if I had to search for 'value' in my projects. Not that cost/price is not important, I just define value differently. To me, it keeps the item from ending up on the curb or attic, and makes for reduced costs to the owner over time by lasting longer than a lifetime or two.
If one follows the 'value' logic, you end up with printed paper facings on partical board, big staples and throw away products as well as time, resources and economics. You end up with WalMart and Ikea as well as bulldozed forests and a huge waste stream. You have to - it is the only place that kind of 'value' will go.
I made a conscious choice years ago to pursue the finest levels of my craft, and to honor the work that went before me that Western Civilization was literally built upon. I have met others that, like me, feel that it is important to continue the tradition and produce work the way it would have in the past to keep the skills alive, to follow in the same or similar steps as those before us. I understand it is a matter of degrees, and it is a frequent point of discussion as to where each individual chooses to draw the line. Even Chippendale had to hold back his workers for a client that did not have the financial horsepower to have the best.
If you look at it as "if I don't do it for XXXprice, then they won't place an order", you are working by dictation. It is thought (tho' debated) that it is better to sell what you make rather than make what you sell. That notion alone is worthy of long reflection.
If you read or talk to successful craftspeople, you will hear something different coming from them, and it is not about making things to fit a price point. Quite the opposite.
I have met makers that have never opened a book on design, or historical photos, or anything to do with precedent other than a google search, and see no reason for the Golden Section, or historical precedent or even good practice. Then there are others that show up at a museum to meet with a curator and they have their wooden measuring instruments, pencils and note pad, as they carefully take a day or two to measure and photograph a piece for reproduction. Or spend hours making models and drafting and working out details before the first board is cut.
Visit the struggling shops and you will hear something more like chasing the wrong kind of "value" - "we can't compete with Home Depot" or Mexicans, or Chinese, or the guy down the street. "I don't need much more than $25.00 per hour...."
Technically, a pocket screw joint will allow the butt glued parts to move in service since the only real hold is mechanical. A tenoned joint will lock in the center third of the joint, so if one piece of wood moves in service, it can only move in 1/3 of its thickness, not the full thickness as with a pocket joint. The glue surface is what holds in a tenon joint - provides the mechanical holding. Butt glue joints are not even joints, as well all know.
I have seen the ever popular carpenter made pocket screwed stile and rail paneling joints that after a few years have moved to out of level. Screws are still tight, but the joint is no longer level and has cracked paint or finish. The fact is, the owner may not even complain, not knowing it as a defect (a huge problem - for another day...). Or worse, the maker doesn't know it as a defect, or even 'worser' yet, has told the owner, "Well you know, it is wood...."
FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards(return to top)
WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
A valid email return address must be included with each message.
Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
Subject lines may be edited for length and clarity.
"Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.
You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.
WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.
Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).
Libel: Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.
Improper Decorum: Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).
Advertising: The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).
Repeated Forum Abuse:
Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.
There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).
The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)
Forum Posting Form Guidelines
The name you enter in this field will be the name that appears with your post or response (return to form).
Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
Thread Related Link and Image Guidelines
Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
Thread Related File Uploads
Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .FLV .MP4 (Image Upload Tips) If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)
The editors, writers, and staff at WOODWEB try to promote safe practices.
What is safe for one woodworker under certain conditions may not be safe
for others in different circumstances. Readers should undertake the use
of materials and methods discussed at WOODWEB after considerate evaluation,
and at their own risk.