CNC

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Help resurfacing mdf spoil board

12/4/15       
stvnhrmn

Homag BOF 311 CNC, BIG vacuum pump with matrix table.

Cannot get enough vacuum through mdf to run a resurfacing program. Breaths too well, software will not run if vacuum requirements are not met. WoodWop programming language (version 5).

Any ideas?

12/4/15       #2: Help resurfacing mdf spoil board ...
Chuck Hicks  Member

Website: http://www.southeasttool.com

Have you sealed the edges with paint or a sanding sealer yet?

Catalog page

12/4/15       #3: Help resurfacing mdf spoil board ...
stvnhrmn

Yes, with an end grain sealer, multiple coats. My issue isn't when using the spoilboard with something (plywood) over it, it's trying to resurface it empty.

12/4/15       #4: Help resurfacing mdf spoil board ...
Chuck Hicks  Member

Website: http://www.southeasttool.com

What is type and HP of Vacuum?

12/4/15       #5: Help resurfacing mdf spoil board ...
stvnhrmn

Dekker VMax, not sure of HP, 300 CFM.

12/4/15       #6: Help resurfacing mdf spoil board ...
stvnhrmn

550 cfm, 40hp, my mistake.

12/4/15       #7: Help resurfacing mdf spoil board ...
Mike

You should contact tech service. You get the alarm due to insufficient vacuum threshold set by the factory. That is adjustable(at least it is on other machines I have worked on). Find out how and dial it down.

12/4/15       #8: Help resurfacing mdf spoil board ...
Chuck Hicks  Member

Website: http://www.southeasttool.com

You should not have a problem with that. May want to contact your machine or software company to see if there is a issue there.

12/4/15       #9: Help resurfacing mdf spoil board ...
Ken

Are you using LDF by chance.
LDF allows to much air flow MDF is the best option.

12/4/15       #10: Help resurfacing mdf spoil board ...
stvnhrmn

MDF. As of now we resort to simply buying a new piece when needed.

12/4/15       #11: Help resurfacing mdf spoil board ...
J Wilson  Member

How thick is your spoil board? We can surface ours down to around 5/16-3/8" before we have to replace it with a new 3/4" thk mdf panel
John

12/4/15       #12: Help resurfacing mdf spoil board ...
Randy

Website: http://rgwoodworkings.com

I have the same problem with all mdf other than plumb dbl refined.I'm hoping to find a solution also. I can't find 5 x 12, so I have to cut 4 x 10s to cove table. It's doable but a pain.

12/5/15       #13: Help resurfacing mdf spoil board ...
stvnhrmn Member

We have been buying 1/2" but I'm going to try 3/4" from here on out. I had another CNC machine my last 1/2" to 3/8" and I get better holding power on my 1/2" so I'll try 3/4" to see how it holds. My tooling and machine are VERY accurate so I can make a new sheet last for months.

12/5/15       #14: Help resurfacing mdf spoil board ...
Jerry Member

Is there a way to close off some of your vacuum to mimic that your spoil board is covered

12/5/15       #15: Help resurfacing mdf spoil board ...
stvnhrmn Member

I've pursued that a little. Seems the less ports I open on the matrix table the more concentrated the suction is where it is open...and again, the mdf is so open it shows even less vacuum overall. I almost wish I could turn down the HP on my pump. I think I'll just resort to getting a new piece when needed.

Thanks for all the feedback!

12/5/15       #16: Help resurfacing mdf spoil board ...
Kerry Fullington

Website: http://windsweptprairiedesign.com

Stvnhrmn

On Thermwood machines we use a 3/4" Table Board (32Lb per cubic foot recommended density) as a base with a 1/4" Wasteboard (48 lb per cubic foot density) on top This eliminates a lot of the bleed through. We replace the wasteboard when it is surfaced to .17"

You should probably look at the CFM of your pump to see if it is moving enough volume of air. The piping to the pump and the table matrix are also factors. The pump can be rated for a lot of suction but if it can't move enough volume of air it won't hold your parts.

Dirty air filters in the pump can also reduce its efficiency.

12/5/15       #17: Help resurfacing mdf spoil board ...
Kerry Fullington

Forgot to mention, make sure your pipe connectors and valves aren't constricting the air flow to the pump. How long is the pipe run to the pump?

12/5/15       #18: Help resurfacing mdf spoil board ...
stvnhrmn Member

Not to be rude, but my problem lies in having too much suction. The mdf I'm trying to resurface isn't even seen by the machine as my pump sucks THRU it so well.

Apparently this isn't a big issue for smaller pumps (like the four other CNC machines at our other facility).

I can't just make a massive spoil board as most of what I do runs on pvc/uhmw pods directly on the table and I have to take my spoil board on and off as necessary. 90% without it so making it massive isn't going to work as I have to lift it off and on manually.

12/5/15       #19: Help resurfacing mdf spoil board ...
Kerry Fullington

Is your gasket material to the matrix table properly sized and sealing properly?

12/5/15       #20: Help resurfacing mdf spoil board ...
Kerry Fullington

Stvnhrmn,

Suction, is what happens when you restrict the flow of air through your spoilboard.
If your spoilboard is allowing too much flow of air through it then the pump needs to move a greater volume of air (CFM) to create suction.
Give us some more info about the pump.

12/5/15       #21: Help resurfacing mdf spoil board ...
Mark

If this is a low plenum pressure alarm, I would really look at the simple and most likely things first because 3/4 standard MDF should be working just fine with just about any pump and any machine.
Have you carefully and thoroughly checked for leaks in your vacuum line? Like Kerry says blockage can reduce the pressure and set off this alarm, but the opposite is true as well, leaks reduce the pressure and the sensor will trigger the alarm. If you have really eliminated this possibility Mike and Chuck are dead on, your sensor may be bad or mis-set. Contact tech and get the real answer, your problem is not likely the MDF.

12/5/15       #22: Help resurfacing mdf spoil board ...
Kerry Fullington

Sorry,

I missed reading above where you gave the pump specs. 550 CFM should be more than enough.

12/5/15       #23: Help resurfacing mdf spoil board ...
Dropout Member

I went from a 10HP Becker to a 30HP rotary screw. I had to lower the switch setting with the rotary screw to get rid of the low vacuum errors. It's likely the high cfm that is causing you the problem.

If you can't adjust the vacuum switch, jumper it out when resurfacing, or, depending on where the switch is, put a ball valve between the switch and the table so you can restrict the flow and increase the vacuum the switch sees.

12/6/15       #24: Help resurfacing mdf spoil board ...
Derrek

Check your gaskets make sure you have a dood seal on the edges. Sometimes our board will start to warp and won't lay flat and leak, so i have jumped up on the table to weight the high spots, once it grabs it will hold.

12/7/15       #25: Help resurfacing mdf spoil board ...
kevin waldron

Website: http://waldroninstrumemts.com

Change brands of material. We had something similar and discovered the material was the culprit along with a bow in the product. If we have vacuum problems we often will cover the table with a roll of polyethylene to find out where our leaks or problems exist. It becomes fairly easy to trace whistle sound when you restrict the draw with the poly.

12/9/15       #26: Help resurfacing mdf spoil board ...
Gerry W

Place 1/2 sheet of laminate on the table to seal off some area. As surfacing tool works its way to the laminate swap positions and let tool finish.

12/9/15       #27: Help resurfacing mdf spoil board ...
stvnhrmn Member

Gerry, that's been my workaround so far. It's a pain, but it works.

12/14/15       #28: Help resurfacing mdf spoil board ...
Mike McClaran

There's an awful lot of talk here for just a simple 1/2 turn of your vacuum sensor.

12/4/20       #29: Help resurfacing mdf spoil board ...
Jason

I use the Aluranger from Casadei. Its an upright. We had the same issue first time we tried to plain a new Spoil board. Turns out that they actually recommended NOT to plane the back side of the spoil board, only the front. tried it and it worked like a charm. went against everything I knew but I was able to plain it empty and it still held my parts like they were fastened to the table. It may not work for your table but it is worth trying. you can always plane it after if it doesn't work.


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)
    Onsrud Cutter Vortex Tool Company T-Tool USA
    Sponsors
    • Limtech Industries, Inc.
      CNC Routers, Machinery for Woodworking, Plastic and Other Non-ferrous Metal Machining Applications
    • Weinig Group-USA
      Wood Moulders and Knife Grinding Equipment
    • NEMI
      Products For CNC Machines - Digitizers, Tool Setters, Vacuum Pods, Vacuum Cups, Vacuum Tables, Vacuum Chucks and Software
    • Southeast Tool, Inc.
      High Quality Tooling at Competitive Pricing
    • MachineryMax
      New and Used Machinery for the Professional Woodworker
    • Safety Speed Manufacturing
      Economical Vertical Panel Saws, Panel Routers, Edgebanders and Widebelt Sanders
    • ULTI-BOARD
      The Ultimate Spoilboard - ULTI-BOARD - Specifically Engineered and Formulated for the Ultimate in Spoilboard Performance - Not Your Ordinary Sheet of MDF.
    • Carter Products
      Band Saw Guides, Blades, Wheels, Tires, Line Lasers and 2D Projectors, Wide Belt Sanding Accessories, Vacuum Holding Systems and More
    • Charles G.G. Schmidt Co.
      Tooling for Shapers, Moulders, Tenoners, Planers and Routers
    • Simantech
      New & Used Machinery, Supplies, Tooling, Parts, and Abrasive Products
    • Holz-Her US Inc.
      Custom Edgebanders, Vertical Panel Saws, CNC Beam Saws, Wide Belt Sanders, CNC Point to Point Boring Machines, CNC Routers
    • Biesse America
      Woodworking Machinery - Machining Centers, Edge Banders, Feeders/Stackers, Panel Sizing Centers
    • EX-FACTORY INC.
      Offering New & Used Woodworking Machinery including Auctions & Liquidations

    Become a Sponsor today!