Solid Wood Machining

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Moulder blanks for glue ups

3/11/17       
Jason  Member

Hello everyone,
I'm currently having problems with glue failure on my glued up stair treads. What is the correct way. I'm making a s4s out of moulder then glueing it up into a stair tread. I was wondering is the moulder finish to smooth for the titebond two to bond to ? Should i put through widebelt to rough up edges to get the glue to bit better. What is the correct order for this process ? Thanks

3/11/17       #2: Moulder blanks for glue ups ...
David R Sochar

You will find some good discussion of glue failure in the archives and Knowledge Base here on Woodweb.

My first thought for your failure is dull knives. You can put a drop of water on a freshly made surface and watch how long it takes to spread out. Long time means the knives are dull and 'glazing' the surface. Sharp knives will allow the water to enter the wood easily and quickly. Makes sense once you see it. The KB will have this info in more detail.

You can also send an example of the failure to your glue vendor and get a professional opinion.

Another thing I have learned recently is that the 'fresher' the surface, the better it will glue. Hours are much better than days.

3/11/17       #3: Moulder blanks for glue ups ...
JR Rutter

David is right. I would suspect knives first.

Widebelt could be problematic depending on the setup. With a rubber drum or soft platen, you could end up with slightly convex edges.

3/11/17       #4: Moulder blanks for glue ups ...
Mark Elliott Member

Jason,

The best edge prep for an edge glued panel is a ripped edge coming off of a SLR or a gang rip saw with good glue line rip blades.

Must faster then a moulder also.

3/11/17       #5: Moulder blanks for glue ups ...
Jason  Member

Thank you everone. Sounds like a good SLR saw will be the answer . I already was looking at new ones cantek or extrema or ironwood from stiles ? They all look like they are coming out of the same plant in tawain . Does anybody have preferance on which one to buy and why ?

3/13/17       #6: Moulder blanks for glue ups ...
Jerry Cunningham

I don't make panels anymore, but when I did I used the moulder to prep the blanks for edge glue as my input lumber was already ripped to width (not glue line) and I needed to make the staves all the same width.

Use a spiral insert head instead of a straight knife head. They tend to give a bi more of an "imperfect" finish that makes for a good gluing surface.

3/13/17       #7: Moulder blanks for glue ups ...
Adam

I agree with the other guys. Sounds like you've got dull knives. They beat the wood smooth versus cut smooth. Its like trying to glue two sheets of plastic together.

3/13/17       #8: Moulder blanks for glue ups ...
JR Rutter

We rarely get a sliver kick back, but even with multiple rows of pawls, a few have managed to slip past and embed themselves in the overhead door in front of the saw. So I would get one with as much anti-kickback protection as possible.

3/14/17       #9: Moulder blanks for glue ups ...
David Rankin

When I prepare material to glue on a moulder, I will generally run the feed a little faster than I would for a high quality finish. for a machine with 6000 rpm spindles I run the feed around 45-50fpm. This creates a slightly rougher finish that seems to help the glue penetrate the material better.

Depending upon the type of glue, you may need to use a better grade of knife steel to cut the finished product after the glue sets. Many companies use carbide while others use DGK knife steel. Using regular HSS can produce nick lines where the glue lines are.

Be Safe,

Dr. David Rankin

http://http://www.moulderservices.com/DGK-Coated-Knife-Steel-5-16-s/65.htm

3/28/17       #10: Moulder blanks for glue ups ...
David Waldmann  Member

Website: vermonthardwoods.com

Maybe I don't have the back story, but I don't understand why a moulder is being used to prepare material for gluing panels.

Typically, moulders are used to prepare a (close to) finished product. The setup time and level of surface preparation tend to be overkill for glue-line level work.

Not to say it can't work, or that for some strange one-off project it's not the best, but it would be near the end of my list of "ways to prepare blanks for gluing into panels"...


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)