Dado Versus Dowel Joinery in Furniture

      It's a trade-off: strength versus cost. January 9, 2007

I have received conflicting views on the benefits of dado versus dowel joints in dorm style, moveable furniture. Some claim that a dado joint is stronger and will prevent racking better than a dowel joint due to the use of glue, even though material is removed to form the dado. Others suggest that a butt joint and dowel construction is stronger. I would appreciate any comment.

Forum Responses
(Furniture Making Forum)
From contributor T:
I repair furniture, from new to antiques. I see a far greater failure rate with dowel construction than with mortise and tenon, which I believe to the correct term, vs dado.

From contributor J:
I use biscuits for my casework, but I think the dado method would be stronger at supporting heavy loads. The dowels will work fine also, it just depends on the piece itself.

If you need more evidence, then build two identical units, one with dadoes and the other with dowels. Now try to make them fail by placing heavier than normal loads and racking them. That's how you will know for sure.

I think contributor T is thinking about actual furniture, not the stuff you find in dorms.

From contributor W:
If you can take the time, I would use shelves with two 2" wide tenons on each end put into corresponding mortises in the sides. A 3/8" deep dado would help also. I am assuming using 3/4" stock (birch ply or solid).

From contributor B:
Mortise and tenon construction provides a large long grain to long grain glue joint. The grain is going in opposite directions, but it is still a large glue face. This makes for a strong glue.

Dowell construction gives very little long grain to long grain mating in the joint. Just look down a cross-grain drilled hole and you'll see there is only long grain on two opposite sides. Since there is little or no strength in butt joint gluing, you end up with a weak glue joint.

That doesn't necessarily mean that dowels make weak joints, though. Whereas you may have a weak glue surface, you still have a joint with a lot of rigidity and shear strength. Plus, you can add as many dowels as wood size reasonably allows.

Bottom line is that your choice will depend upon the end value of your product. A mass produced inexpensive item easily justifies doweled construction. On the other end of the scale, a museum quality piece deserves the extra time and attention required to produce mortise and tenon joints.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Furniture

  • KnowledgeBase: Furniture: Furniture Manufacturing

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - WOODWEB ® Inc.
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review WOODWEB's Copyright Policy.

    The editors, writers, and staff at WOODWEB try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at WOODWEB after considerate evaluation, and at their own risk.

    WOODWEB, Inc.
    335 Bedell Road
    Montrose, PA 18801

    Contact WOODWEB

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article