De-Warping Table Leaves

      A draw-leaf table has warped, and the maker asks for advice on fixing it. Colleagues suggest ways to quickly straighten the crooked parts. October 19, 2005

I designed and built a Dutch drawleaf dining room table two years ago. The table is made of white oak and finished with catalyzed lacquer. The top is 30mm thick and the extension leaves store under the top on the ends and can be pulled out and popped up to add 18 inches on each end of the table. I made the top and the leaves as one single glue-up with the grain running the length of the table. Since I used clips in grooves in the apron, the main top has stayed nice and flat, but as you may have guessed, the leaves have warped and now the outside edges droop (about 1/4" to 3/8") and the extension is no longer flat with the top when extended. I now realize that I should have used a breadboard end (possibly both ends of the extensions) or something, but I was too preoccupied with maintaining the continuous grain pattern from the top to the extensions.

How can I fix the problem? My thought is to cut tenons on the ends and add a breadboard end (or both ends), but how do I straighten the leaves to accept the cross-end breadboard piece or is there some other remedy that I could use? Would removing the finish and dampening the concave side work?

Click here for full size image

Photo by Richard Erickson

Forum Responses
(Furniture Making Forum)
I think you are on the right track thinking about stripping and using moisture to get the leaves straight so you can machine them. It would be a pain, but it could work. One other thing you could try that is also a pain would be to use a heat source to get them flat. Many times when I have a problem panel or something that cups, I set it near the woodstove (not too close!) in my shop and since a panel tends to go hollow on the heated side, I place the convex side of the cupped panel toward the stove.

In either case, you will have to work fast and probably even stop and reflatten a few times during the process of adding the breadboard ends. I am having a problem in my shop right now with some wide maple boards required on a project that won't stay flat. I tested the stock for casehardening and I believe that is the problem. In the future I will try to get air dried stock because it will have zero casehardening and casehardening is what causes cupping. Also, of course on wider boards, it is advisable to rip them and glue them back together, which will break the continuity of the grain and if you get cupping, you will get two or more small cups instead of one large one. One other important thing to remember is that the thicker the stock, the less cupping you will get.

You don't even need to strip them - they warped with the finish on, right? Just take some damp towels and put them on the shrunk side with a sheet of plastic on the other side of the towel to prevent them from drying out. Do this in the morning, and then check every hour - it should straighten out by the end of the day. Then add breadboards, both to the leaves and the top. Incidentally, we make a lot of tables with this mechanism and I have only done it in solid once. It's a lot safer to do it with a veneered top and leaves.

Click here for full size image

Click here for full size image

Click here for full size image

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Furniture

  • KnowledgeBase: Furniture: Furniture Repairs

  • KnowledgeBase: Wood Engineering

  • KnowledgeBase: Wood Engineering: General

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - WOODWEB ® Inc.
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review WOODWEB's Copyright Policy.

    The editors, writers, and staff at WOODWEB try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at WOODWEB after considerate evaluation, and at their own risk.

    WOODWEB, Inc.
    335 Bedell Road
    Montrose, PA 18801

    Contact WOODWEB

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article