Glue Applicator Choices

      Cabinetmakers discuss efficient, non-messy ways to apply glue to solid wood staves when making up door panel blanks. July 10, 2009

I have a question about the glue spreader below. It is used for distributing glue on staves that will be laminated together for raised panels etc. The concept seems pretty simple. A perforated metal pan lives in a pond of glue. As you step on the lever at the bottom this pan raises to present a pattern of glue that you press the long edge of a stick onto.

How viable is this approach for a small shop? Does the glue have such a short pot life that clean up for the machine would wipe out any labor gains from the machine?

Also: are there any better ways to distribute glue on a long stave? We get way more squeeze out than I want and it is always a painful experience to either wipe it off when wet or scrape it when dry. Does anybody have a better solution for getting the right amount of glue along the edge of a laminated board?

Click here for higher quality, full size image

Forum Responses
(Cabinetmaking Forum)
From contributor T:
We use a pressurized glue tank. Itís a Scheenburge and has 15 years worth of glue on it. I can't read the label. We have two lines coming off it, one for 8M dowels and another for biscuits. Nozzles twist on/off. When not in use the nozzles sit attached to squeeze trigger in a coffee can filled with water. All this is on a little rolling cart set up for this. There are many different nozzles available.

From contributor D:
We considered one of these long ago, but ended up with a glue roller from Virutex. The Virutex has a top wheel the partially rests in the glue. You roll your piece across it.

From the original questioner:
The problem I am trying to solve is one of uneven distribution and/or too much glue. We usually only coat one edge of the lamination and leave the other one dry. The extra glue squeeze out is what I am trying to manage. This is a messy thing to clean up when glue is wet and takes a lot of muscle when the glue is so hard it needs to be scraped. We sometimes try to time the glue-ups such that the glue can harden enough to scrape but not be so hard it takes Hercules to get the job done. We flatten these panels on the jointer after glue up and it would be nice to not have so much excess glue passing over the jointer knives. It would be great to find some kind of applicator. I'm thinking that the pressurized pot contributor T mentions would be worth looking at. I'm guessing you could engineer a fence on the glue applicator to keep the glue bead centered where you want it and maybe some kind of spreading mechanism that follows the glue bead?

From contributor D:
Your fence idea would work with this item. The top roller is textured rubber, which better controls the glue application. It's small, easy to clean and cheap enough that that you could try it and see.

From the original questioner:
That looks interesting. Did you not say you tried and abandoned this method? If so, what is the roller made of? Is it hard to clean?

From contributor D:
We did try this method and eventually abandoned it. However, we do so little edge gluing that I don't think my experience is a good barometer. Knowing what I know, I think your vertical fence idea is a good one. Basically, the rubber roller just lifts off. You rinse it in the sink and dump it in a bucket of water until next use. The glue pot simply gets the lid put on. Supposedly you can mist some water on top of the glue and will keep longer. The roller is hard rubber with a diamond texture imbedded into it. From what I recall, it applied the perfect amount of glue with only pinhead size beads squeezing out.

From contributor A:
JLT makes a smaller version of your glue applicator. It works about the same but is not as long and holds less glue so it stays fresher longer. Ourís used to get a dry crust between jobs on top of the glue. We switched to Titebond brand and that problem went away. We do about three kitchens a month and the glue stays fresh.

Squeeze-out does occur but that is better than a starved joint. We never scrape or joint panels after glue up. Unnecessary non-value added steps. I thought scraping was needed until I talked to another cabinet maker who did not scrape. I tried it and never looked back. Iíve never had a problem plugging widebelts or planer blades. Our panels are flat and true coming out of the sander. Run them at an angle so the glue lines don't have a chance to build up on the belts.

We glue up panels with the good side up in the clamp. Run though the sander (planer/sander now) good side down on the first pass. The glue levels out more on the good side of the panel as it dries in the clamp. It is flatter and truer than the dried drips on the bottom side so is true enough to run on the feed belt of the sander.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Cabinetmaking

  • KnowledgeBase: Cabinetmaking: Cabinet Door Construction

  • KnowledgeBase: Adhesives, Gluing and Laminating

  • KnowledgeBase: Adhesives, Gluing and Laminating: Gluing and Clamping Equipment

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2020 - WOODWEB ® Inc.
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review WOODWEB's Copyright Policy.

    The editors, writers, and staff at WOODWEB try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at WOODWEB after considerate evaluation, and at their own risk.

    WOODWEB, Inc.
    335 Bedell Road
    Montrose, PA 18801

    Contact WOODWEB

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article