Green Douglas Fir for Timber Framing

      Advice on framing with fresh-cut Douglas Fir posts and beams. April 2, 2013

I will be cutting some freshly harvested 20" diameter fir to be used for a post and beam timber framed cabin. The cabin will be a total of 1000 sq feet.

What should the moisture content be before I use this timber in the cabin? I will be air drying the beams in my shop. The average temperature should be around 60 degrees and I will use a vast amount of circulated air over the stacks. How long do you think it will take to dry a 6" X 18" beam if I start with a moisture content of over 40%? What should the final moisture content range be before I use my beams?

Forum Responses
(Sawing and Drying Forum)
From Professor Gene Wengert, forum technical advisor:
Let me suggest that having this much moisture in your shop will create all sorts of problems, including rust or corrosion of metal. Coastal D-F is often quite dry when first cut (under 40% MC), but even then you do not want that much moisture in your shop. Perhaps you can rent an 18-wheeler van and leave the doors open for venting and use fans to stir the air, etc. Contact the Oregon Forest Products Lab for specific advice.

Regarding MC, due to the low initial MC of coastal D-F, in the past buildings would use the timbers in above ground locations as is, and then let them air dry during construction. The checking that developed was considered acceptable. Further drying would occur when the building was closed and heat turned on, which would mean more checking and shrinking in diameter, and rarely some warp. To be safe, drying the wood to 12-15% MC would probably be wiser overall as the wood would change less in use.

From contributor F:
In my region in France we use a lot of Douglas fir for this kind of framing. Douglas fir has a relatively low shrink ratio, so it can be used undried in some situations.

Your beams can take a long time to dry, so I agree with Dr. Wengert's suggestion. But I think you should consider the following. For framing you should pay attention on these conditions:

If the framing is going to be drawn in insulation the wood must be dried to less than 18% MC because moisture can't escape afterwards, so fungus guaranteed!
For ordinary wall framing, the building time can be sufficient.
Be sure your client is aware that some cracks, splits and joints opening will occur later on.
Beware of heavily loading a green lumber frame because warping can be twice to three times as bad than if the same lumber were dried.

If you can, go with this :
Try to avoid having the heart of the tree in the beams, because this can cause split and also cause the piece to curve.
For posts, split can be okay (only compression). If you have the heart in a beam, place the beam so that the heart is in the upper section. The curve will go upwards and the compression side is more forgiving.
If the lumber must be dried because the above conditions are to be avoided, the best solution is glued lumber for those huge measurements (sorry, I don't know the proper name in English).
Here are two photographs of the roof frames in my workshop, made from freshly sawn Douglas fir. This is to give you an idea of what you can do with green Douglas fir if you pay attention to how to place the pieces.

From contributor F:
A few additions…
We use a lot of undried Douglas fir for framing.
I meant the suggestion of using your beams as they are. (Unless fungus risky places.)
The building time can be sufficient if the building is roofed, correctly ventilated and you have something like 2 months to spend before insulating. Install exterior sheeting to avoid moisture gain from rain. Best is to check MC before insulating.
Never put undried wood (joists) in a masonry wall!

From the original questioner:
Thanks for your help. I was able to cut all of the beams that I need last week and I have them stickered, covered from the sun and air drying. Your post and beam work looks fantastic.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Adhesives, Gluing and Laminating

  • KnowledgeBase: Primary Processing

  • KnowledgeBase: Primary Processing: Sawmilling

  • KnowledgeBase: Wood Engineering

  • KnowledgeBase: Wood Engineering: General

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - WOODWEB ® Inc.
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review WOODWEB's Copyright Policy.

    The editors, writers, and staff at WOODWEB try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at WOODWEB after considerate evaluation, and at their own risk.

    WOODWEB, Inc.
    335 Bedell Road
    Montrose, PA 18801

    Contact WOODWEB

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article