Locating a Long Straight-Edge

      How to make (or where to buy) a durable and accurate 12-foot-plus straight edge. March 14, 2006

I was just wondering where you guys get your long (12' 6") straight-edges? The only ones I have used are from Pinske. I need another one, but those are pricey and I thought I would shop around.

Forum Responses
(Laminate and Solid Surfacing Forum)
From contributor A:
Look at the Eurekazone SGS EZ Smart Guide System. It is a little expensive also, but it looks like a nice set up.

From contributor B:
Have you considered making it out of Solid Surface?

From contributor C:
You might want to check with a local metal fabrication shop and see what they would charge to fabricate one for you.

From contributor D:
It depends on what you are using the straight edge for. The tolerances for solid surface are a lot tighter than for laminate. I do mostly laminate. For my seams I went to the local metal supply yard and purchased a piece of aluminum approximately 1/4" x 3 7 long. I had them cut in half, and sanded it with 220 grit to clean it up. It gives me perfect laminate seams. I also have had good luck with buying aluminum angle iron as a straight edge for my router and saw.

From contributor E:
I use 3/4" MDF for my straight edges. It's available in 145" lengths. It's stable if you keep it dry, reasonably durable, and cheap. If you hit it with your router you don't ruin your bit, just buzz a quarter inch off the affected edge and it's good as new. I laminate the edges. It's also softer than solid surface so it doesn't damage my tops. Find someone with a nice panel saw to rip it for you. My twelve footer is 12" wide to prevent flexing.

From contributor F:
We purchase aluminum stock from a metal supplier. This is cheaper than buying from a metal fabricator. The aluminum from the supplier comes in twenty-foot lengths that we have cut to our desired lengths. We then cut the edges on our CNC router to true them up. We find this very quick and inexpensive. The CNC step is critical in these types of straight edges because the tolerance for straightness from a metal supplier is much less than what you would purchase from Pinske. If you do not have a CNC, it would still be cheaper to have a metal fabricator make them for you. Just be sure that they true the edges for you.

From contributor G:
We purchase steel straight edge tools from a supplier to flooring companies. Aluminum is too soft, and subject to router burns. We've used different phenolic straight edges, including Pinske's, but they show wear on the edges that we depend on.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Laminates and Solid Surfacing

  • KnowledgeBase: Laminates & Solid Surfacing: Equipment

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - WOODWEB ® Inc.
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review WOODWEB's Copyright Policy.

    The editors, writers, and staff at WOODWEB try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at WOODWEB after considerate evaluation, and at their own risk.

    WOODWEB, Inc.
    335 Bedell Road
    Montrose, PA 18801

    Contact WOODWEB

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article