Octagonal tapers

      Instructions for making octagonal table legs, tapered on all eight sides. June 13, 2001

I'm looking for tips on making octagonal table legs with tapers on all eight sides.

Forum Responses
Let's assume that you want the legs to be 2" across at the top and 1" on the bottom.

First, cut 2" wide non-tapered octagonal blanks on the table saw. Now go to the jointer and lower the infeed table so it takes off 1/2".

Next take the leg and lower it over the cutter head so that the top 1/2" or so of the blank is resting on the out-feed table (this will cause a small snipe, so make sure you're holding the blank firmly). Push it through and you'll be taking off a 1/2" taper from the blank.

If taking off 1/2" at a time makes you nervous, you can set the in-feed table to 1/4" and make two passes.

Repeat the same operation for the other 7 sides.

At this point, the leg will be tapered to size but will have a small bit of snipe on each face where you started the taper. To get rid of this, just raise the in-feed table and clean up each face in the conventional way.

If the legs are shorter than the length of the in-feed table, you can clamp a stop block to it so you'll be starting the taper in the same exact spot every time without having to eyeball it (safer, too).

The comments below were added after this Forum discussion was archived as a Knowledge Base article (add your comment).

Comment from contributor A:
If you're making larger quantities, an automatic lathe is the way to go. From a rough blank to ready for sanding, you can do about two legs a minute! The drawback is setup time. You'll have a full day or 2 in the setup. Like I said... gotta do a lot of them to justify it.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Furniture

  • KnowledgeBase: Furniture: Custom Furniture

  • KnowledgeBase: Furniture: Furniture Manufacturing

  • KnowledgeBase: Furniture: General

  • KnowledgeBase: Solid Wood Machining

  • KnowledgeBase: Solid Wood Machining: General

  • KnowledgeBase: Woodworking Miscellaneous

  • KnowledgeBase: Knowledge Base

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2020 - WOODWEB ® Inc.
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review WOODWEB's Copyright Policy.

    The editors, writers, and staff at WOODWEB try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at WOODWEB after considerate evaluation, and at their own risk.

    WOODWEB, Inc.
    335 Bedell Road
    Montrose, PA 18801

    Contact WOODWEB

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article