Steam-Bending a Pre-Turned Part

      Bending wood that has already been turned is difficult, if not impossible. August 6, 2010

Is it possible to steam bend a piece of wood that has already been turned, as opposed to turning a square or rectangular blank?

Forum Responses
(Furniture Making Forum)
From contributor R:
It's still wood, right? Still has lignin in it? Bend away.

From contributor L:
It depends on a long list of variables, but in general, I'd answer a qualified yes. Know that as the piece bends, it flattens a bit, so instead of a round turning, you wind up with an oval shape. A photo or drawing showing species, turning pattern, size and radius would help. And that's only the beginning.

From contributor H:
If the turning is anything but a round dowel, you will have trouble. The thicker parts of the turning will not give as easily as the thinner parts. So expect the thinner, smaller diameter areas of the turnings to break or crack, leading to an uneven bend.

From contributor T:
I made some chairs once that had a curved square leg at the bottom and were turned at the top. I cut the curve first and made a jig that held the square part of the leg on the lathe for turning. It's a traditional technique you will find in turning books. Steam bending a turned piece won't do the finished turning any favors.

From contributor C:
It can't be done unless it is very gentle, it wasn't kiln dried, and you have a suitable bending species. Here is why... Your turning is probably from KD wood. If it is green, or partially air dried, you have half a chance to get a modest bend. Wood that is KD is past its prime for bending, though there are some exceptions for modest bending needs. Target 15 to 25% MC for bending. Then, consider that steam bent parts need a backing strap for anything but the most modest bends to force compression to the inside of the curve rather than stretching on the outside of the curve. You can't really put a backing strap on a turned spindle. And finally, it will bend at the thinnest points. If you think you are bending a modest radius curve, all the bend will be taken up in the thinner parts of the spindle, putting too much stress on those areas, that you also can't get a backing strap on.

While it can be done if you plan ahead, most likely your pre-turned part won't survive. If you do it, have some spares. Steam bending at first is a trial and error endeavor, and that is with S4S stock, a backing strap, the right species, the right moisture content, and effective steaming. If it is ash, red oak, white oak, hickory, elm, beech, hard maple, black locust, cherry or walnut, you have something to work with. Otherwise, probably not.

Would you like to add information to this article?
Interested in writing or submitting an article?
Have a question about this article?

Have you reviewed the related Knowledge Base areas below?
  • KnowledgeBase: Knowledge Base

  • KnowledgeBase: Furniture

  • KnowledgeBase: Furniture: General

  • KnowledgeBase: Woodworking Miscellaneous

  • KnowledgeBase: Woodworking Miscellaneous: Bending Wood

    Would you like to add information to this article? ... Click Here

    If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
    review our Forum Guidelines.

    Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

    When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

    Return to beginning of article.

    Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

    Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

    Contact us to discuss advertising or to report problems with this site.

    To report a problem, send an e-mail to our Webmaster

    Copyright © 1996-2021 - WOODWEB ® Inc.
    All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
    Review WOODWEB's Copyright Policy.

    The editors, writers, and staff at WOODWEB try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at WOODWEB after considerate evaluation, and at their own risk.

    WOODWEB, Inc.
    335 Bedell Road
    Montrose, PA 18801

    Contact WOODWEB

  • WOODWEB - the leading resource for professional woodworkers

      Home » Knowledge Base » Knowledge Base Article