Architectural Woodworking

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Post a Response
The staff at WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at any WOODWEB Forum. Participants should undertake the use of machinery, materials and methods discussed after considerate evaluation, and at their own risk.
Your Name:
Your Website:
Email Address:
Subject: Re: Controlling snipe on a W&H

Message:

(read message guidelines).
Note: Do not use the below fields to advertise your business - only for links related to the discussion.
Thread Related Link URL:
Thread Related Link Title:
  To "point" to an image (picture) from another website, provide the URL (Web Address) of the file ( include ONE reference to http:// )
Thread Related Image URL:

Date of your Birth:

Upload a Thread Related File:
File Types: Image (gif-jpg-png-bmp), PDF, Sketchup, Video (mov avi wmv mpeg mpg mp4 ogg). (Image Upload Tips)

I have read the Site User Agreement and agree with the Terms

  <= Check to receive e-mail notification of responses

Message Thread:

Controlling snipe on a W&H

8/9/17       
Mark B Member

We recently ran a large order (for us) of hard maple case and base. We struggled throughout the whole thing with snipe mainly on the out feed end of the cut but occasionally on the infeed as well (so we would have 6-8" of waste on each end of some pieces).

Hard maple is always a major b***h for us. I hate the stuff. We ran all this material in 2 and in some cases 3 passes but still fought it the whole way even on a 3 pass which seems ridiculous to me as it wasnt an overly deep profile. Perhaps 9/16" to 5/8" max stock removal at the deepest part of the profile.

It was almost like on the out feed end the molder would pick up that last 6 of unsupported material (once it was no longer held down by the infeed roller). We tried lifting heavily on the outfeed side which helped occasionally, oddly, endless board seemed to help a lot (which we try to do by default).

It was a brand new set of knives.

Just wondering if anyone has any input.

8/9/17       #2: Controlling snipe on a W&H ...
Tony Darbenzio

Had the same problem until i bought the
multi-pass kit & the variable speed kit.

https://www.williamsnhussey.com/collections/accessories/products/copy-of-m
ulti-pass-kit-mp-06-green-k

https://www.williamsnhussey.com/collections/access
ories/products/vari-feed-kits-vf-104-k

8/9/17       #3: Controlling snipe on a W&H ...
rich c.

I put a dado head on the table saw, and power feed the stock through it to remove excess material. Do you have any tables or supports? Essential running long stock.

8/9/17       #4: Controlling snipe on a W&H ...
Leo G

Make sure when you are feeding things through that you are always butting the next pc tight to the one that is finishing up in the molder.

I've made myself some infeed and outfeed tables that have helped greatly in the quality of the moldings.

I also made this gadget to lock down the open side of the molder to prevent chatter.


View larger image

8/10/17       #5: Controlling snipe on a W&H ...
TimG

Look at where the arms that hold the rubber feeders stop against the stop pins, mark it with a pencil. Take them out and grind a slot big enough to allow the feeders to lower about 1/4'', you can now take 2-3 passes rather than one huge one. Guy at the W&H booth at a trade show 30 years ago showed me,works great.

8/10/17       #6: Controlling snipe on a W&H ...
Mark B Member

Thanks guys,
We do have infeed and outfeed support rollers but they are not very far from the molder, perhaps a foot or sixteen inches. Building some in and out feed tables seems to be in order.

Leo, I have seen your tip with blocking and clamping the cantilevered side of the molder and I have never tried it but I dont feel like we get much chatter but I am going to try it next round for sure.

Tim, I will have to look in there to see if I can understand what your saying. Will run out and give it a look today.

Thanks again.

8/10/17       #7: Controlling snipe on a W&H ...
Mark B Member

Tim, I think I see what your saying. Grinding the slot allows the rollers to drop down much farther. We dont have a ton of problems taking multiple passes most of the time. But Im going to give this some thought before I pull them out. I think I get what your saying. Makes sense.

8/10/17       #8: Controlling snipe on a W&H ...
B.H. Davis Member

The multi-pass kit (or modifying the machine to those specs yourself) will help but not completely solve the problem.

The multi-pass kit will let the feed rollers drop lower, better holding the wood down on the machine table. Longer, softer springs are then used to hold the rollers in that lowered position. This helps put more pressure on the wood.

However this is only part of the solution. On the outfeed side we will apply upward pressure on the board about 3' to 4' out from the machine, and then downward pressure with the other hand right up by the machine. This forces the end of the moulding down onto the table so it won't lift up into the knives.

On the infeed side we do the same thing but with the downward pressure hand further back for safety.

End snipe is nothing more than the ends of the board lifting off the table surface and raising up into the spinning knives. The above described hand pressure method will help to keep the ends of the board down. Some end snipe will still occasionally occur but this helps a lot.

BH Davis

8/10/17       #9: Controlling snipe on a W&H ...
Sawkerf

I struggled with this for years and recently I started lifting up on the piece as it nears the end and it completely eliminates snipe.

8/11/17       #10: Controlling snipe on a W&H ...
Adam

The method BH is describing is used on any planer that doesn't have strong feed rollers.

Anyone that has used a shaper with a feeder deals with it in exactly the same way. Its a learned feeling in your hands.

8/11/17       #11: Controlling snipe on a W&H ...
David R Sochar Member

I will second Adam's support of Bernie Davis's third paragraph - about support and counter support for things going into and out of planers.

This is fundamental.

Some of the old cast iron beasts needed no support in or out on the lumber it was planing, but most smaller shop planers still need help. I have an 18" P-Matic with adjustable feed rollers so it runs tight, but I still have the habit of bending the thinner stock on the way in and especially on the way out towards the end. No snipe whatever.

8/11/17       #12: Controlling snipe on a W&H ...
Leo G

Yup, it's a tactic I use on the last pc of molding coming out of the W&H. Usually when they are run end to end you don't get snipe. Sometimes I use the test pc as the last board which helps eliminate the end snipe.

But it also matters on how much material you are removing. If you are taking a big cut then it's likely no matter what you do, you'll end up with some snipe.

Larger moldings are run in 2 passes (or more). That way you can just run a kiss cut on the final pass. But depending on the molding it might not work. I have moldings that are raised on one edge and very shallow on the other. The rollers won't bend that much to keep full contact on both sides. So you have to take a lighter 1st cut which retains contact for the second pass with both sides of the molding and the 2nd pass is where you take off to the final thickness.

8/11/17       #13: Controlling snipe on a W&H ...
Mark B Member

We have always done the raising up on the outfeed side but I can see the advantage of the two hand approach applying down pressure close to the machine and bowing the piece up on the outbound hand.

Its odd that the endless board method helps so much even without raising the outfeed part.

On this last run we took to 3 passes, which sucks, leaving the last pass at just a crank or half crank down on the handle. Still gave some fits. We dont run a ton of hard Maple (thankfully) and have used most of these techniques over the years in some capacity and never had the issues with snipe we had on this job.

Working it all into the plan but Im still chalking a bit of it up to devil wood (even though I know there are much much worse species)

11/19/17       #15: Controlling snipe on a W&H ...
Larry

Hard maple molds beautifully! One pass, full depth. To limit snipe you can also make sure to feed the lumber in so any curve to it makes the ends go down rather than up. Doing 3 passes at the extremely slow feed rate of a W&H is really expensive! Job it out to a shop with a molder.

 

Buy & Sell Exchanges | Forums | Galleries | Site Map

FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)