Architectural Woodworking

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

large wood corbels

6/22/14       
M Smith

I'm going to be building two large ( 24" deep x 34" tall x 6.5" wide) wood corbels to support a custom hood surround. Finish is white paint/lacquer so i am very concerned about glue joint lines telegraphing down the road IF i do a solid slab glue up. Alternately, i might do more of a "composite" type of fabrication- 5/4 solid "sides" with spacer blocks glued in to get the 6.5" , bending poplar at curves, maple veneer as a final scalloped face in the curved and flat sections, small roundover to ease the edges. Question- what type of glue for the Maple veneer, was thinking cold Hide glue. Is there a better method to fabricate from solid with the goal of never seeing glue joint lines telegraph thru the paint ???

M Smith


View higher quality, full size image (1840 X 3264)

6/22/14       #2: large wood corbels ...
Larry

Think I'd skip the veneer near a range and make it hollow with solid face. Use a hard setting glue with tight fit. Give it some time after cutting before final sanding to let the moisture even out.

7/2/14       #3: large wood corbels ...
Dale Skipper  Member

Website: http://www.oaktrim.com

I agree with Larry regarding veneer near a range; lots of potential moisture steaming up on those corbels over the years.

We made some large ones similar but not paint grade, they were Cherry. We edge glued 8/4 together than sandwiched glued those pieces. So, we ended up with visibly glue joints but they did not look bad. I considered the veneer application for that job but was too concerned with the proximately to the range.

Let us know how you make out!

Best regards,

Dale

7/6/14       #4: large wood corbels ...
M Smith

Ended up doing a "hollow" type construction with maple lumber core panels and then psa backed maple veneer for the scalloped face . Came out good but only time will tell if it stays tight over the long haul ??? If I had more time I would vac bag the veneer with hide glue - yes I said hide glue .
M Smith

7/6/14       #5: large wood corbels ...
M Smith

Pics of corbel fab


View higher quality, full size image (1840 X 3264)


View higher quality, full size image (1840 X 3264)


View higher quality, full size image (1840 X 3264)

7/6/14       #6: large wood corbels ...
Larry

The advantages of hide glue and why it is used for traditional musical instruments is it is easily reversable. Making it possible to repair them as needed. Heat and moisture are used to loosen it. Are you sure it would be your choice for use around a range?

7/6/14       #7: large wood corbels ...
M Smith

I thought the same thing but after talking to Mr Patrick Edwards ( leading expert on Hide glue and maker of Old Brown Glue) he assured me that the heat/moisture needed to reverse hide glue has to be concentrated right on the joint and even given the close proximity of these corbels to a cooktop it would not be an issue - in his opinion ,which I respect . Also read somewhere u can add "alum" powder to hide glue to make it "waterproof/resistant".
M Smith

7/6/14       #8: large wood corbels ...
Dale Skipper  Member

Website: http://www.oaktrim.com

Great Job M Smith!

Those corbels look fantastic!

Best regards,

Dale

7/7/14       #9: large wood corbels ...
M Smith

Dale -
Thanx - they were a lot of work !!! Ended up using PSA backed maple veneer for the scalloped face, only time will tell if they stay put. If I had more time I would have vac bagged them with hide glue (cold version) .

M Smith


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)