Can anyone suggest a good way to route a continuous 1/4" x 1/4" dado on all four sides of a 3 1/2" square (16" long) block of wood? The cut is complicated by the fact that 2/3's of the 16" length is tapered on all four sides so I can't just use a simple stop block as I would if the stock were not tapered. I made a simple sled for my router table which allows me to visually line-up each cut with the previous cut in--combination with the edge of the router bit's path through the plywood base--but it's time-consuming and not perfectly accurate. At least one dado ends up being a few thousands higher or lower than its neighboring dado. Since I'm using a 1/4" inlay all around this uneveness creates visual issues. I think I need to devise a fence/guide instead, as that would guarantee each cut is equal distance from the bottom of the stock, and then use a hand held router. But 3 1/2" isn't long enough for a fence so I would have to extend it somehow while also stabilizing the wood block somehow. Any ideas?
9/20/14 #2: routing a continuous dado around co ...
This is a dado gross grain at 90 degrees to the 16" length? As in banding that runs around a table leg?
If so, you are making square stock before you taper, so do the dado before the stock is tapered. Then do the taper, leaving the dado at the correct placement and depth. This requires the dado to be deeper than you doing so after the taper, depending upon where you need the dado.
As for the router method; after tapering, your inaccuracy is caused most likely by one (or more) of three things: the angle of the sled is slightly off, or the taper is not a consistent angle from face to face, or the stop block you register from is not contacting at the exact same point on the stock as you rotate it.
In looking at these sorts of problems, it is helpful to determine what things are easier to control than others. Know what you can reliably control and take control, leave the rest aside.
As our buddy Donald Rumsfield says, There are known knowns, and known unknowns, and also unknown unknowns.
9/20/14 #4: routing a continuous dado around co ...
Thanks to all for the feedback. David R. I hope you got my email. Rich, I like the concept but not sure I'm visualizing it correctly. Looks like you're suggesting a jig/pattern that fits over the square end (to be precise, a 3 1/2" cubed end) of my 16" piece. The stock and jig would be horizontally positioned. The jig would have a straight edge, i.e. pattern, 90 degrees to the stock for the bushing to ride against and, on top, a "shelf" extending out from the stock enough to accommodate the base of my router as it travels the 3 1/2" distance. For each new side the piece would be turned 90 degrees and the jig/pattern reinserted on the end. That would work but I would still need some type of micro adjustment to align the router bit perfectly with the previous cut. Even a minor deviation would throw off the alignment of adjoining dados on opposing sides. Am I barking up the right tree here or am I totally off base?
9/22/14 #6: routing a continuous dado around co ...
Like David said:
1. Square stock 3.5' x 3.5' x 16"
2. Using a miter gauge or sled on the table saw cut the dadoes around the bottom of the leg.
3. Glue the contrasting wood into the dadoes.
4. Taper the leg.
Reverse 4 and 3 if you need to, then plane the inlay to match the taper.
FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards(return to top)
WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
A valid email return address must be included with each message.
Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
Subject lines may be edited for length and clarity.
"Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.
You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.
WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.
Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).
Libel: Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.
Improper Decorum: Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).
Advertising: The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).
Repeated Forum Abuse:
Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.
There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).
The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)
Forum Posting Form Guidelines
The name you enter in this field will be the name that appears with your post or response (return to form).
Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
Thread Related Link and Image Guidelines
Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
Thread Related File Uploads
Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips) If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)
The editors, writers, and staff at Woodweb.com try to promote safe practices.
What is safe for one woodworker under certain conditions may not be safe
for others in different circumstances. Readers should undertake the use
of materials and methods discussed at Woodweb.com after considerate evaluation,
and at their own risk.