Furniture Making

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Advice on a trestle table with leaves

12/20/17       
Rick W

I need advice about the best way to design a trestle table that can expand in length.
Here are the details: Solid wood (walnut) construction, top approx 42 X 72, extending to 42 X 120. Top will be solid, 1-1/8" to 1-1/4" thick.The grain of the top will be running lengthwise, with breadboard ends. The base will be a trestle, with two pedestals connected by rails, and the finished height will be about 33".
My question is how to add leaves to this table, given that the top is solid wood. If I make the leaves with the grain running in the same direction, I'll have two leaves about 42" wide X 24" long. That seems to almost guarantee warping. However, if I make the leaves with the grain going across the width, that will contrast with the rest of the top.
I am considering using regular table slides to expand the top. The client would like for the leaves to pull out from the table, but I can't think of a way to accommodate that. A Dutch pull-out might work, but is a 24" overhang at the ends too much?
I would appreciate any advice.
Thanks,
Rick W

12/20/17       #2: Advice on a trestle table with leav ...
rich c.

How are you going to mount the top if you use slides? If you screw the center of the slide to some stretchers, the top is going to expand in it's width. So any solid fastening of the slides to the base is going to put the top in a bind. 33" is way too tall in my book. I make most of my tables 29 to 30". I always consider how the people will sit when doing leaves. At 42" wide, two can sit on the end if they favor themselves to the outside. I usually figure 24" per person. Now you have those people on the edge, and then it gets them too close to the person that centers up on 24" leaf pulled from the end of the table.

12/21/17       #3: Advice on a trestle table with leav ...
duster

Website: http://sunvalleywoodworks.com

There are several ways to do leaves in a trestle base table. If you want to pull the top apart and put leaves in the center, you will need to build a frame with a solid bottom that's attached to the top of your trestle base. Steel bottom mount slides have flanges that mount to the bottom of your frame and to the underside of your top. The frame has to be sized to accommodate the slides travel and length of your leaves. leevalley.com carries these slides in several lengths. To keep your leaves flat, screw some solid wood cleats approximately 1.25 x 2" to the underside on each end of your leaves. To accommodate seasonal wood movement, counterbore your cleats on the ends about 3/4" deep on the edge against the underside of your top. This will allow your top to expand or contract without splitting the top or breaking a screw. I've built quite a few tables this way and never had a problem.


View higher quality, full size image (800 X 390)


View higher quality, full size image (800 X 390)

12/26/17       #4: Advice on a trestle table with leav ...
Rick W

Thanks for the responses. Both were helpful.
Rich, I had planned to make a framework to attach the slides to. However, duster's idea of a platform and the Lee Valley slides may work better. The table will be higher than normal because my client is tall and wants the extra leg room. However, I may be able to accommodate that without making it so high.
Duster- nice work! Thanks for pointing out the Lee Valley slides and your method of attaching them. I think that will work for my table. Does the table you show have a solid top and leaves?
Thanks,
Rikc

12/27/17       #5: Advice on a trestle table with leav ...
David R Sochar Member

Most people, tall or not, that want more leg room at a table actually want the apron to be very narrow or gone. Apron to chair seat clearance is what is wanted so they can cross their legs, etc. A trestle table typically will have no apron, so will solve that.

Also, a tall table will put anyone else at the table ill at ease, with their plates at chin level. You might seriously consider removing 1" in height from the client's chair.

At any rate, mock it up directly in front of him to be sure before you start cutting wood.

When I first started out on my own, I would take odd requests and think I was doing the world a favor, finding a niche, etc. After a couple of reworks once the clients got what they ordered and saw where they went wrong, I relied on my knowledge of design and historical precedent to keep everybody happy.

The housewife that demands seating 16 at an 8' long table by making it 10' wide gets a quick math and design lesson, and is sent off, unfulfilled. At least by me.

12/27/17       #6: Advice on a trestle table with leav ...
duster

Yes Rick, that table was all solid alder except the 3/4 ply base I used in the frame to attach the slides.

I agree with David that 33" is too tall for a dining table, and would make your clients guests feel like a little kid at the adult table. Maybe that's the point...

That being said, a new trend is bar height dining tables that use barstools instead of chairs. I've done a couple lately including this one in walnut that was 60 wide x 84 long x 36 high. The designer put 10 barstools around it.


View higher quality, full size image (800 X 422)


View higher quality, full size image (800 X 420)


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)