I am wondering if anyone can shed some light on specific gravity settings on Wagner mmc220 pinless meter? The listed SG for american elm in wagner book is .50. I have found the Wood Database online to be an excellent resource. He is listing the SG of American Elm to be .56 at 12%. The question arises because I am attempting to kiln dry some 2" thick American Elm. It was consistently losing 1% to 2% per day until it reached around 10%. It has been stuck there for a couple days now. I am having some issues with my Nyle L53 at temps above 140 so I am set at 136 dry bulb 100 wet bulb. That is as hot and dry as I can achieve right now. I don't want to deceive myself by setting meter to higher SG but if set to .56 SG it reads 1% to 2% lower MC. The other question that I wrestle with is is it practical or even necessary to hold out for 6% to 8% MC on thick material that is intended use is table tops and bar tops? If it gets finished and put into service at 10% MC in Minnesota will I experience some undesirable warping or failure? Thank you for any wisdom and experience you might be able to share!
Hi Nathan. I have the same meter that basically measures density. it could just give a reading like an ohm meter that you could look up on a chart, but they allow you to put in a generic estimate of that woods density. The water adds to the density and as the wood dries and becomes lighter, it becomes less dense. If you change the setting to a higher wood specific gravity, It will show less moisture content as it attributes more of the density to the wood and not the moisture. The sell a calibration block if you think your meter is the problem. I am not a kiln person, but I wonder if with that thickness it will take longer to get to your goal MC. How long has this been drying? As you know knots will read higher, sap wood less. Also thin boards like 1/4 inch will read lower. Might try the oven drying method to see where the wood is really at.
The density that the Wagner meter uses is the green density. You do not adjust this density as the wood dries. So, use the values in their book, unless the wood you are testing is abnormally high or low in density. In fact, it is the natural variability of density of the same species that causes some confusion with this pinless meter.
You must indeed get the wood to a low MC, thick or thin, for use in MN or just about any environment that is heated. The environment is around 30% RH which means 6.0% EMC. So, any lumber above 7.0% MC will dry a little bit more and with drying comes shrinking and possibly warp.
If nice and dry, then when summer comes, the wood will gain several percent lister, but because there is approximately a 1% delay before swelling begins when moisture is added, and because swelling tends to be less of an issue than shrinking, we are not too concerned. In my book, the ideal is 6.5 to 6.8% MC.
Note that a 36 F depression at 100 F is under 3% EMC, so your wood should be drying toward that value. If it is not drying, then either you MC is wrong or the DB and WB are wrong...stick a small, thin piece of wood in the kiln and then use the oven test to check its MC which will also be the EMC. The pinless meter will not work on a small piece. Also, the pinless meter tends to give a higher reading for thicker stock.
Very true and well stated Gene. so gases and liquids tend to be more consistant, but solids like wood has a lot of variation. The meter is set to an overall estimate of specific gavity for that type of wood so it can estimate the MC from the density measured above what is expected. The SG of water is 1, and therefore wood with a SG of .55 is less dense than water and will float. That wood is thick and wondering if it needs more time or heat. Gene is clearly the expert and would let him comment on that.
Thanks for the input. I have been trying to post a response, but after pressing post message it vanishes and I have to start over? Maybe they will all show up someday?
I checked with pin meter and come up with mostly 0%... a couple 5%. I don't think it works below 3 or 4%?
I am as sure as I can be it is American Elm.
Pinless meter still reads as low as 7% and as high as 16%. Mostly around 10 to 12%
I need to know what you all with more experience and wisdom would do as a kiln operator in this situation. I also need to know I am producing a quality product my customers will be pleased with for years to come
Gene, I think you were right to question whether I have properly identified the species of elm. Both trees were standing dead when I cut them. One matches perfectly all the american elm pics I can find. The other is a bit darker in color. Does not really match any other elm pics I can find. I am beginning to think it is rock elm, which would explain a lot. Switch wagner meter to SG of .63 for rock elm and readings are in the 7 to 8% range.
Between that revelation and the pin meter readings I am thinking I can pull the load and move on. Would you all agree?
I believe that when you look at the end grain of American elm with 10x magnification, you will see only a single row of large open vessels at the beginning of each growth ring. The other elms have several rows. If you google "American elm Hoadley", I believe you will see a picture from his book. Or try link below
The mystery continues in my mind...I attempted to examine the end grain. The slabs I have came from two different trees. As I said both standing dead when I cut them. End grain appears to be the same in regards to the single row of vessels in earlywood. I did notice an obvious difference in the density of the rings. The larger tree (30" + diameter) has very wide rings. The other that is such a mystery in regards to MC read on pinless meter has rings so tight in areas you can hardly tell them apart. I have always understood each light part of the ring(early wood?) followed by the darker ring (late wood) combined indicates one year of growth in most species? I was conservative when counting some of these very tight rings and came up with some where around 225 rings on a 16" diameter tree! Is that even possible? I will attempt to attach pics. First two are the dense one still getting readings on pinless meter as high as 14% even set at .63 for rock elm. The other is the wider ringed larger tree.
FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards(return to top)
WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
A valid email return address must be included with each message.
Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
Subject lines may be edited for length and clarity.
"Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.
You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.
WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.
Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).
Libel: Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.
Improper Decorum: Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).
Advertising: The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).
Repeated Forum Abuse:
Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.
There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).
The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)
Forum Posting Form Guidelines
The name you enter in this field will be the name that appears with your post or response (return to form).
Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
Thread Related Link and Image Guidelines
Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
Thread Related File Uploads
Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .FLV .MP4 (Image Upload Tips) If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)
The editors, writers, and staff at WOODWEB try to promote safe practices.
What is safe for one woodworker under certain conditions may not be safe
for others in different circumstances. Readers should undertake the use
of materials and methods discussed at WOODWEB after considerate evaluation,
and at their own risk.